8
ENGLISH
(Original instructions)
Lubrication oil is available from your BLACK+DECKER dealer
(cat. no. A6102-XJ).
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u After use, carefully clean the blades. After cleaning, apply
a lm of light machine oil to prevent the blades from rust-
ing.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be tted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new
plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the tting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Protecting the environment
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Troubleshooting
Problem Possible Cause Possible Solution
Slow
running,
noisy
or hot
blades.
Dry, corroded blades.
Blades or blade support
bent.
Bent or damaged teeth.
Loose blade bolts.
Lubricate blades.
Straighten blade or blade support.
Straighten teeth.
Tighten blade bolts.
Unit will
not start.
Lock off not fully
operated.
Cord not plugged in.
Circuit fuse is blown.
Circuit breaker is
tripped.
Cord or switch is
damaged.
Check that lock off is fully forward
prior to moving main trigger.
Plug cord into a working outlet.
Replace circuit fuse.
(If the product repeatedly causes the
circuit fuse to blow, discontinue use
immediately and have it serviced at a
BLACK+DECKER service center or
authorized servicer.)
Reset circuit breaker. (If the
product repeatedly causes the circuit
breaker to trip, discontinue use
immediately and have it serviced at a
BLACK+DECKER service center or
authorized servicer.)
Have cord or switch replaced at
BLACK+DECKER Service Center or
Authorized Servicer.
Technical data
BEHTS551
Type 1
Voltage V
AC
230
Power input W
650
Blade strokes
(no load)
min
-
1
1840
Blade length
cm
60
Blade gap
mm 25
Blade brake
time
s
<1
Saw blade Max
cut
mm
35
Weight
kg 3.1
Level of sound pressure according to EN 62841:
Sound pressure at operator position (L
pA
) 87.5 dB(A), uncertainty (K) 1.1 dB(A)
Sound power (L
WA
) 98.5 dB(A), uncertainty (K) 1.3 dB(A)
Vibration total values (triax vector sum) according to EN 62841:
Vibration emission value (a
h, D
) 3.8 m/s
2
, uncertainty (K) 1.5 m/s
2
EC declaration of conformity
MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
BEHTS551 – Hedge Trimmer
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 62841-1:2015; EN 62841-4-2:2019
2000/14/EC, Hedge trimmer, Annex V, DEKRA Certication
B.V. Meander 1051 / P.O. Box 5185
To Next Page
Loading...
