ENGLISH
(Original instructions)
6
When rst starting:
When the tank has run out of water.
Fill the receptacle taking care to observe the MAX level
Connect the appliance to the mains.
Press the on/off switch (F) to ON position. The (E) pilot
light will come on in red colour
You do not have to wait for the machine to heat up for
this operation
Without tting the lter holder (H) (or with the lter holder
tted, but without coffee), place a recipient under the
position of the coffee cup
Select the coffee position by rotating the D control to this
position
Water will exit through the lterholder position. Wait until
approximately one cupful has exited
To nish serving, rotate the selection control D to the
central position 0
This will complete the priming operation.
Filling with water:
The tank must be lled with water before turning the
appliance on.
Remove the water tank.
Open the cover.
Fill the tank taking care to observe the MAX level
Close the lid.
Replace the tank in its housing, ensuring that it is well
tted.
Filling Coffee:
Remove the lter holder (H)
Position the selected ground coffee lter (J or K) in the
lter holder
Attention
Filter extraction
The lterholder includes a spring inside, whose function
is to avoid the fall of the sieve when throwing the used
coffee. That spring produces a lateral tightening on the
lter
Due to this tightening, to remove the lter for exchange
or cleaning, it may be necessary to use a tool.
We recommend using a roundtipped knife or a tip of a
teaspoon, so that it can be placed between the upper
edge of the lterholder and the bottom of the sieve wing
A small turn will cause them to separate from each other
and will facilitate the extraction
Filter J (smaller one) can be used either for ground
coffee or paper pods
We recommend using natural toast coffee, as using
some roasted coffee may affect the operation of the
machine.
Fill the chosen removable lter (1 or 2 cups) with ground
coffee (6-7 g per cup to be prepared).
Using measuring spoon (I) for 1 coffee, put 1 spoonful
and for 2 coffees, put in 2 spoonfuls.
Next lightly press down the ground coffee with the back
of the spoon.
Before tting the lter holder in the coffeemaker assem-
bly, turn the ladleholder backwards.
Fit the lter holder in the appliance once more.
Position the lter holder in the coffee assembly by inser-
ting the assembly downwards and turning it anticlockwi-
se, from left to right, until it locks.
USE
Connect the appliance to the mains.
Turn the appliance ON using the on/off switch (F)
The (E) pilot light comes on red intermittently
Wait until the pilot light E change it’s lighting to blue. It
means right temperature is reached
Place one or two preheated cups at the lter holder
outlet.
Turn the Control Knob (D) to the coffee position
The coffee infusion will begin to exit. When you have ob-
tained the desired quantity of espresso coffee (short or
long), turn back control knob (D) to the central position 0
Once serving has nished, wait a few seconds and
remove the cups with the coffee.
Remove the lter holder and empty the grounds from it.
Wash the lter holder with running water and dry it well.
Check that the removable lter is perfectly tted into the
lter holder.
Fit the lter holder in the appliance once more.
NOTE: After the espresso is brewed, the machine
automatically creates a bit of steam and pushes the
remaining water from the pump into the drip tray. This
ensures that there will be no restwater in the heating
system. After preparing a few cups of espresso, carefully
pull the drip tray out of the machine, empty and replace.
Preparation of coffee with paper single
dose (PODS):
If you want to use Single paper doses (POD)
Remove the ground coffee lter from the lter holder (K)
Introduce in the lter holder, the singledose lter (J)
Then put the POD in the lter holder; Make sure that the
To Next Page
Loading...
