7. Top cover
8. Water outlet
9. Water tank
10. Water level gauge
11. Main housing
12. Rocker switch
Before first use
• Warning! Do not use the appliance without the reservoir
filled.
Check that all accessories are complete and the unit is not
damaged. Fill water into water tank to the MAX level and
brew water for several times without coffee powder, then
discard the water. Clean and dry all detachable parts
thoroughly according to the section “Cleaning And
Maintenance” .
Using your coffee maker
1. Open the top cover and fill the water tank with fresh
water. The water level should not exceed MAX level as
indicated on the water level gauge.
2. Add coffee powder into filter. Usually a cup of coffee
need a level spoon of coffee powder, but you may adjust
according to personal taste. Then assemble the filter
with coffee powder into the funnel, and maker sure the
funnel is fitted properly, otherwise the top cover can not
be closed. Finally, close the top cover.
3. Insert the carafe on the warming plate horizontally.
4. Plug the power cord into the outlet.
5. Press Power switch to “I” position, the indicator will be
illuminated. The appliance will begin working.
6. The brewing process can be interrupted by pressing
Power switch to “O” position. The appliance will continue
brewing once the Power switch is pressed to “I” position
again.
Note: You can take out carafe, pour and serve at any time.
The appliance will stop dripping automatically. But the time
cannot exceed 30 seconds.
Caution: DO NOT touch cover, warming plate and so on
when operating as they are very hot.
7. When the process is finished, if you do not want to serve
immediately, keep the coffee maker is energized, the
coffee can be kept warm in the warming plate. For an
optimum coffee taste, serve it just after brewing.
Note: Please make sure the carafe is not empty when
keeping warm to avoid dry boiling.
8. Remove out carafe to serve when finish brewing (about
one minute later after the coffee stops dripping out.)
Note: The coffee you get will less than the water you have
5
ENGLISH
(Original instructions)
added, as some water is absorbed by coffee powder. DO
NOT touch cover, warming plate and so on when operating
as they are very hot.
9. Always turn the coffee maker off and disconnect the
power supply when not use.
Note: Pay attention to pour the coffee out, otherwise you may
be hurt as the temperature of coffee just finished is high.
Cleaning and maintenance
CAUTION: Be sure to unplug this appliance before cleaning.
To protect against electrical shock, do not immerse cord, plug
or unit in water or liquid. After each use, always make sure
plug is first removed from wall outlet.
1. Clean all detachable parts after each use in hot sudsy
water.
2. Wipe the exterior surface of unit with a soft, damp cloth to
remove stains.
3. Water droplets may buildup in the above area of the
funnel and drip onto the product base during brewing. To
control the dripping, wipe off the area with a clean, dry
cloth after each use.
4. Use a damp cloth to gently wipe the warming plate.
Never use abrasive cleaner to clean it.
5. Replace all parts and keep for next use.
Descaling the appliance
(Removing mineral deposits)
To keep your coffee maker operating efficiently, periodically
you should clean away the mineral deposits left by the water
according to the water quality in your area and the use
frequency, we recommend removing mineral deposits as
follows:
1. Fill the tank with water and descaler to the max level as
indicated on the water level gauge (the scale of water
and descaler is 4:1, the detail refers to the instruction of
descaler. Please use “household descaler”, you may also
use the citric acid instead of the descaler (the one
hundred parts of water and three parts of citric acid).
2. Insert glass carafe onto the warming plate.
3. Make sure filter (without coffee powder) and funnel are
assembled in place.
4. Switch on the appliance and allow it to “brew” de-scaling
solution by follow the operation above.
5. After “brew” one-cup solution, switch off the appliance.
6. Leave the solution stay for 15 minutes and repeat step
3-5.
7. Switch on the appliance and run off the solution until the
water tank is completely empty.
8. Rinse by operating the appliance with water at least 3
times.
To Next Page
Loading...
