ELECTRONIC PROGRAMMER
The programmer can select the following
functions:
-Clock (set by keys 2 and 3)
-Minute counter (set by key 1)
-Cooking time (set by key 2)
-End of cooking (set by key 3)
-Manual operation mode (set by key 4)
-To decrease the time (set by key 5)
-To increase the time (set by key 6)
The digital display (N) always shows the time
and can display cooking and end of cooking
time or the minute counter time by pressing the
corresponding push button.
N.B.: At the end of each setting session (except
for the minute counter) the programmer turns
the oven off. Check when next using the oven,
if the programmer is not going to be used, that
the latter is set on manual operation (see the
instructions given further on).
Setting the time (from 0.01 to 24.00 = hh,mm)
After connecting to the electricity mains or
subsequent to a power cut, AUTO and “0.00” will
both ash simultaneously on the display.
Press push buttons 2 and 3 simultaneously and
start setting the current time by pressing push
button 5 or 6.
Once set the AUTO symbol will turn off
and
the symbol, for manual operation, will turn
on.
Minute counter (from 0.01 to 0.59 = hh,mm)
Press push button 1 and select cooking time with
push button 5 or 6. The symbol turns on. At
the end of the set time the buzzer will go off and
the symbol turns off.
Semi-automatic operation
(with cooking time from 0.01 to 23.59 = hh,mm)
By pressing push button 2 and setting the length
of cooking time with push button 5 or 6, the AUTO
and symbols will light up and stay on all the
time. At the end of the set time the symbol
will turn off, the AUTO symbol will ash and the
buzzer will go off.
Semi-automatic operation
(with end of cooking time from 0.01 to 23.59 =
hh,mm)
By pressing push button 3 and setting the end of
cooking time with push button 6, the AUTO and
symbols will turn on and stay on all the time. At the
end of the set time the symbol will turn off, the
AUTO symbol will ash and the buzzer will go off.
Oven Setting:
After setting a program, turn the oven function
selection knob to the desired oven function and
set the oven thermostat knob to the desired
cooking temperature.
Automatic operation
(with the start of cooking time delayed)
First programme cooking time (both the AUTO
and symbol will turn on) and then the end
of cooking time (the symbol will turn off) as
described previously. The symbol will turn on
again when baking in the oven starts. At the end
of cooking time the symbol will turn off, the
AUTO symbol will ash and the buzzer will go off.
Manual operation
Manual operation is only possible when the
automatic programming has nished or after
having cancelled it by pressing push button 4. The
AUTO symbol disappears and the symbol
turns on.
Buzzer
The buzzer will go off at the end of a programme or at
the end of the minute counter function and lasts about 7
minutes. The buzzer can be stopped by pressing one of
the function push buttons.
Programme start and control
The programme starts after setting. The programme
set can be controlled at any time by pressing the
corresponding push button.
Correcting/cancelling the programme setting
An automatic function programming error will occur if the
time shown on the clock is between the cooking start
time and cooking end time. This error will be signalled
immediately by a buzzer and the AUTO symbol will
ash. A setting error can be corrected by altering the
duration or end of cooking time. Any programme that
has been set can be corrected at any time by pressing
the corresponding programming key and then key 5 or
6. To cancel a programme, correct the time set bringing
it to a value of “0.00”. If functioning time is cancelled
the end of functioning is cancelled too and vice versa.
The oven turns off automatically and the AUTO symbol
ashes. Press key 4 to set the programmer on manual
operation. The right time cannot be corrected when the
automatic operation programme is working.
DESCRIPTION OF THE APPLIANCE
To Next Page
Loading...
Need help?
General
