BleBox SwitchBox User Manual

switchbox v1
intelligent device switch
in μWiFi technology
Do not connect loads with a power greater than the permissible
one.
Connect in accordance with the scheme presented in the manual.
Incorrect connecon can be dangerous, it can
result in damage to the controller and loss of warranty.
DANGER! Danger to life due to electric current (also with the de-
vice o), voltage may be present at the outputs. All assembly work
should be carried out ALWAYS with the circuit disconnected
power.
Connecng the device to the power grid without the quality re-
quirements specied in the standard
PN-EN 50160 results in the loss of warranty.
1
INSTALLATION - BASICS
SAFETY RULES
CONNECTION DIAGRAM
CONTROL DEVICES FROM ANYWHERE IN THE WORLD
Before installing the driver, disconnect the power supply
perimeter. Remember that all assembly work should be carried out at
disconnected supply voltage (disconnecng the mains installaon fuse
or unplugging the power cord from the outlet).
The controller should be installed in a place protected against
unfavorable environmental condions, protected against third pares access – in
a ush-mounted box or inside the controlled housing
devices. Remember that metal parts (wires, housing parts) negavely aect the
range of the device, and thus the comfort of using. It is advisable that the device
be xed in posion
stable and staonary. Necessary due to the operang voltage of the device is that
the connectors in the controller are protected against accidental touch or short
circuit that may result in electric shock or damage to the device.
Familiarize yourself with the diagram and then proceed to the installaon of the
controller. Pay parcular aenon to the labeling of the controller connectors.
Start with connecon of the power supply wires - phase L (brown color) and neu-
tral N (blue). Then connect the load. If you decide to local control from a
wall switch, plug in also switch, according to the diagram. For control via
smartphone or tablet only, no wall switch is required.
The controller supports all types of single monostable switches (so-called
bell switches).
Aer making sure that the device has been connected in accordance with
the diagram and that there are no metal elements near the controller that
could accidentally short-circuit the contacts, turn on the device by swit-
ching on the power supply (switching on the mains installaon fuse or con-
necng the power cord to a socket).
FIRST START
2
Unlock your phone or tablet and download the free wBox applicaon. If
you have an Android device, the applicaon can be found in the Play store.
For iOS devices, the applicaon is available in the App Store. The Windows
Phone app can be downloaded from the Windows Phone Store.
Using a mobile phone or tablet, connect to the device’s wireless network.
To do this, enter the sengs of your smartphone or tablet, then to the
conguraon of the WiFi network and nd the network called “switch-
Box-xxxxxxxxxx ” where xxxxxxxxxx is the serial number of the device.
Connect with this one network.
Turn on the wBox applicaon. You will see your device at the top of the
screen. To add it to the applicaon, click “+” on the right side, next to
the name. To preliminarily congure the driver, click on the default device
name.
Test the operaon of the controller by clicking the ON / OFF buon,
paying aenon to connected load behaviour. If you connected a wall
switch, check its operaon. In the default conguraon for monostable
buons (so-called bell buons), holding the buon key should turn on the
load, releasing the buon will turn the load o. To change this behaviour,
go to sengs (buon “Sengs” in the upper right corner of the screen)
and then in the opon “set acons for input”, for the corresponding acon
(you can set up a maximum of 10 acons
for the buon) select the appropriate acon type for the given trigger. For
example, to alternately turn the light on / o with the monostable buon
each me it is pressed, select the acon type as “change state” and select
“short press” as the trigger.
Also, check the selecon in the “state aer reboot” which determines the
method behaviour of the controller aer a restart caused by e.g. a break in
the supply of electricity. You can choose if the load should stay on, o, stay
in the pre-reboot state (if it was on it should remain turned on, if it was
turned o, it must remain turned o), or take the opposite.
You can also congure it using the phone/tablet web
browser. Aer connecng with the wireless network of
the controller, turn on the browser and go to the websi-
te: hp://192.168.4.1
user manual
device
ACCESS POINT AND WIFI
NETWORK SETTINGS
3
Aer you run the controller for the rst me, you can proceed to its fur-
ther conguraon. Being connected to the WiFi network broadcast by
the device, select the device on the control panel of the wBox applicaon,
then go to sengs (“Sengs” buon in the upper right corner screen).
You can change the name of the device under which it is displayed in the
applicaon wBox. In addion, you can change the name and password of

BleBox SwitchBox Specifications

General

Brand	BleBox
Model	SwitchBox
Category	Switch
Language	English