CMX44CS USER MANUAL
Contact: support@blustream.com.au | support@blustream-us.com | support@blustream.co.uk
15
RS-232 Configuration and Telnet Commands
COMMAND ACTION
? / HELP Print Help Information
STATUS Print System Status And Port Status
FWVER Print All Firmware Version
PON/POFF Power On Or O Device
REBOOT Set System And Network Reboot
IR ON/OFF Set System IR Control On Or O
KEY ON/OFF Set System KEY Control On Or O
BEEP ON/OFF Set Onboard Beep On Or O
LCD ON/OFF
Set Front Panel LCD Always On
Or Auto Turn O In Power On State
RSB x
Set RS232 Baud Rate to X bps
x=[0:115200 1:57600, 2:38400, 3:19200, 4:9600]
RESET Reset System To Default Setting
RESET ALL
Reset System And Network To Default Setting
(Should Type ""Yes"" To Confirm, ""No"" To Discard)"
OUT xx ON/OFF Set Output:xx On Or O
OUT xx SCALING yy
Set Output:xx Video Mode yy
xx=00: Select All Output Port
xx=[01...04]: Select One Output Port
yy=[01]: Select Output Port Video Mode Bypass
yy=[02]: Select Output Port Video Mode Force_1080p
yy=[03]: Select Output Port Video Mode Match TV
OUT xx FR yy Set Output:xx From Input:yy
EDID xx CP yy Set Input:xx EDID Copy From Output:yy
EDID xx DF zz
Set Input:xx EDID To Default EDID:zz
xx=00: Select All Input Port
xx=[01...04]: Select One Input Port
yy=[01...04]: Select One Output Port
zz=00: HDMI 1080p@60Hz, Audio 2CH PCM zz=12: DVI 1280x1024@60Hz, Audio None
zz=01: HDMI 1080p@60Hz, Audio 5.1CH DTS/DOLBY zz=13: DVI 1920x1080@60Hz, Audio None
zz=02: HDMI 1080p@60Hz, Audio 7.1CH DTS/DOLBY/HD zz=14: DVI 1920x1200@60Hz, Audio None
zz=03: HDMI 1080i@60Hz, Audio 2CH PCM zz=15: User EDID 1
zz=04: HDMI 1080i@60Hz, Audio 5.1CH DTS/DOLBY zz=16: User EDID 2
zz=05: HDMI 1080i@60Hz, Audio 7.1CH DTS/DOLBY/HD zz=17: GUI Download EDID
zz=06: HDMI 1080p@60Hz/3D, Audio 2CH PCM zz=18: HDMI 4K@60Hz 4:2:0, Audio 2CH PCM
zz=07: HDMI 1080p@60Hz/3D, Audio 5.1CH DTS/DOLBY zz=19: HDMI 4K@60Hz 4:2:0, Audio 5.1CH DTS/DOLBY
zz=08: HDMI 1080p@60Hz/3D, Audio 7.1CH DTS/DOLBY/HD zz=20: HDMI 4K@60Hz 4:2:0, Audio 7.1CH DTS/DOLBY/HD
zz=09: HDMI 4K@30Hz 4:4:4, Audio 2CH PCM zz=21: HDMI 4K@60Hz 4:4:4, Audio 2CH PCM
zz=10: HDMI 4K@30Hz 4:4:4, Audio 5.1CH DTS/DOLBY zz=22: HDMI 4K@60Hz 4:4:4, Audio 5.1CH DTS/DOLBY
zz=11: HDMI 4K@30Hz 4:4:4, Audio 7.1CH DTS/DOLBY/HD zz=23: HDMI 4K@60Hz 4:4:4, Audio 7.1CH DTS/DOLBY/HD
PRESET STATUS Print Preset Config Status
PRESET pp SET aa,bb,cc,dd Set Preset:pp Config
PRESET pp SAVE Save Current Output Connection To Preset:pp Config
PRESET pp APPLY
Apply Preset:pp Config To Output Connection
pp=[01..08]: Select Preset Index
aa=[01..04]: Output 01 From aa, [00]: Not Set
bb: Output 02 ... dd: Output 04
AUD RX xx ORG Input Port:xx Use Original Receive HDMI/DVI Signal
AUD RX xx ANA Input Port:xx Embeded Analogue L/R To HDMI/DVI Signal
AUD RX xx AUTO
Input Port:xx Embeded Analogue L/R When DVI Signal
xx==[00]: All Input Port, [01...04]: Input Port
NET DHCP ON/OFF Set Auto IP (DHCP) ON Or OFF
NET IP xxx.xxx.xxx.xxx Set IP Address
NET GW xxx.xxx.xxx.xxx Set Gateway Address
NET SM xxx.xxx.xxx.xxx Set Subnet Mask Address
NET RB Network Reboot and Apply New Config!!!
NET TN xxxx Set Telnet Port
NET DNS xxxx Set DNS Domain Name To xxxx
To Next Page
Loading...