BluStream MX44VW - RS232 and Telnet Commands - Detailed List; Command Reference for EDID and Modes

MX44VW USER MANUAL
18
www.blustream.co.uk
RS232 COMMAND DESCRIPTION
? Print Help Information
HELP Print Help Information
STATUS Print System Status And Port Status
PON Power On, System Run On Normal State
POFF Power O, System Run On Power Save State
IRON/OFF Set System IR Control On Or O
KEYON/OFF Set System KEY Control On Or O
DBGON/OFF Set Debug Mode On Or O
BEEPON/OFF Set Onboard Beep On Or O
RESET Reset System To Default Setting (Should Type “Yes” To Confirm, “No” To Discard)
OUTxxON/OFF Set OUTPUT:xx On Or O
OUTxxFRyy Set OUTPUT:xx From INPUT:yy
EDIDxxCPyy
Copy EDID from output (yy) to input (xx)
Both yy & xx can be set individually (01-08) or as ALL (00)
EDIDxxDFzz
Set Input:xx EDID To Default EDID:zz
xx=00: Select All INPUT Port
xx=[01...04]: Select One INPUT Port
zz=00: HDMI 1080p@60Hz, Audio 2CH PCM
zz=01: HDMI 1080p@60Hz, Audio 5.1CH PCM/DTS/DOLBY
zz=02: HDMI 1080p@60Hz, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=03: HDMI 1080i@60Hz, Audio 2CH PCM
zz=04: HDMI 1080i@60Hz, Audio 5.1CH PCM/DTS/DOLBY
zz=05: HDMI 1080i@60Hz, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=06: HDMI 1080p@60Hz/3D, Audio 2CH PCM
zz=07: HDMI 1080p@60Hz/3D, Audio 5.1CH PCM/DTS/DOLBY
zz=08: HDMI 1080p@60Hz/3D, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=09: HDMI 4K2K, Audio 2CH PCM
zz=10: HDMI 4K2K, Audio 5.1CH PCM/DTS/DOLBY
zz=11: HDMI 4K2K, Audio 7.1CH PCM/DTS/DOLBY/HD
zz=12: DVI 1280x1024@60Hz, Audio None
zz=13: DVI 1920x1080@60Hz, Audio None
zz=14: DVI 1920x1200@60Hz, Audio None
OUTMODEmm
Set Output mode:
mm = MX (matrix)
mm = MV (multi-view)
mm = VW (video wall)
mm = MV01, MV02 etc (multi-view layout 1, layout 2 etc)
mm = MV01, MV02 etc (multi-view layout 1, layout 2 etc)
mm = VW22 (video wall 2x2), VW41 (video wall 4x1), VW14 (video wall 1x4 )
OUTMVFRyy Set Multi-View Main window (window 1) from input yy (01-04)
OUTVWFRyy Set Video Wall Output from input yy (01-04)
OUTxxVCLbb
OUTxxVCRbb
OUTxxVCTbb
OUTxxVCBbb
Pixel shi when in Video Wall mode
xx = Output port (01-04 or 00 for all outputs)
VCL = Le boarder
VCR = Right boarder
VCT = Top boarder
VCB = Bottom boarder
bb = Pixel shi (00-100)
INxxFRyy
Set input video type to HDMI or VGA
xx = Input port (01-04 or 00 for all inputs)
yy = HDMI (from HDMI signal)
yy = VGA (from VGA signal)
MVAUDaa
Multi-View audio output from input aa
aa = 01-04 (inputs)
aa = 00 (audio will follow output/window 1)
RS232 and Telnet Commands (Continued)