RESmart
©
Heated Humidifier User Manual V2.6
P3
Warnings & Cautions
IMPORTANT! • Read all instructions before using the humidifier.
• Use only with BMC RESmart devices whose instructions specify the use of this humidifier.
CAUTIONS! • Indicates the possibility of damage to the device.
• US federal law restricts this device to sale by or on the order of a physician.
• If fluids are spilled onto the humidifier platform, unplug the power cord from the AC
wall outlet and allow the humidifier platform to drain and dry before using.
• Take precautions to protect furniture from water damage.
WARNINGS! • Indicates the possibility for injury to the user or the operator.
• Use the humidifier only for its intended use as described in this manual.
• Use only accessories recommended by BMC.
• Never operate the humidifier if any of the parts are damaged, if it is not working
properly, or if the humidifier has been dropped or mishandled. Do not use the humidifier
if the water chamber is leaking or damaged in any way. Have any damaged parts replaced
before continuing use.
• Never touch the heater plate unless the humidifier is unplugged and the plate has cooled
down.
• This equipment is not suitable for use in the presence of a flammable anesthetic mixture
with air or with oxygen or nitrous oxide.
• Periodically inspect the power cord for signs of wear or damage. Replace if necessary.
•Do not operate the device in direct sunlight or near a heating appliance because these
conditions can increase the temperature of the air coming out of the device.
• When humidifier is used outside the specified ambient temperature range or humidity
range, the performance of humidifier will be compromised.
Symbols
Attention, Consult Type BF Applied part Class II (Double Insulated)
Accompanying Documents
DC Power IPX1 Drip-Proof, Vertical European CE Declaration
of Conformity
RESmart
©
Heated Humidifier User Manual V2.6
P11
Guidance and manufacturer's declaration - electromagnetic immunity
The RESmart is intended for use in the electromagnetic environment specified below. The user of the
RESmart should make sure that it is used in such an environment.
Electromagnetic environment -
guidance
Electrostatic
discharge (ESD)
IEC 61000-4-2
Floor should be wood, concrete or
ceramic tile. If floors are covered with
synthetic material, the relative humidity
should be at least 30%.
Electrical fast
transient/burst
IEC 61000-4-4
±2 kV for
power supply lines
±1 kV for
input/output lines
±2 kV for
power supply lines
±1 kV for
input/output lines
Mains power quality should be that of a
typical home or hospital.
±1 kV
differential mode
±2 kV
common mode
±1 kV
differential mode
±2 kV
common mode
Mains power quality should be that of a
typical home or hospital.
Voltage dips,
short
interruptions and
voltage
variations on
power supply
input lines
IEC 61000-4-11
<5 % U
T
(>95% dip in U
T
)
for 0.5 cycle
40% U
T
(60% dip in U
T
)
for 5 cycles
70% U
T
(30% dip in U
T
)
for 25 cycles
<5% U
T
(>95% dip in U
T
)
for 5 s
<5% U
T
(>95 % dip in U
T
)
for 0.5 cycle
40% U
T
(60% dip in U
T
)
for 5 cycles
70% U
T
(30% dip in U
T
)
for 25 cycles
<5% U
T
(>95% dip in U
T
)
for 5 s
Mains power quality should be that of a
typical commercial or hospital
environment. If the user of the RESmart
requires continued operation during power
mains interruptions, it is recommended
that the RESmart be powered from an
uninterruptible power supply or from a
battery.
Power frequency
(50/60 Hz)
magnetic field
IEC 61000-4-8
If the pressure deviates more than is
indicated in the device specification, it
may be necessary to position the
RESmart further from sources of power
frequency magnetic fields. The power
frequency magnetic field should be
measured in the intended installation
location to ensure that it is sufficiently low.
NOTE: U
T
is the AC mains voltage prior to application of the test level.
To Next Page
Loading...
Need help?
General
