188 S650 Operation & Maintenance Manual
DIAGNOSTIC SERVICE CODES (CONT'D)
Service Codes List
Figure 296
Service Codes may be either a word (Item 1) or a number
(Item 2) [Figure 296].
The following word errors may be displayed:
[REPLY] One or both instrument panel(s) not
communicating with the controller.
[CODE] The controller is asking for a password.
(Keyless Start and Deluxe Instrumentation Panels
only.)
[ERROR] The wrong password was entered.
(Keyless Start and Deluxe Instrumentation Panels
only.)
[SHTDN] A shutdown condition exists.
[DOOR] Operator cab door is open. (Lift and Tilt
functions will not operate.)
P-76461H
P-76461P
P-76455G
1
2
CODE DESCRIPTION CODE DESCRIPTION
A3623 ACD not programmed A8503 ACD output ‘F’ error OFF
A8002 ACD output ‘A’ error ON A8505 ACD output ‘F’ short to battery
A8003 ACD output ‘A’ error OFF A8506 ACD output ‘F’ short to earth
A8005 ACD output ‘A’ short to battery A8507 ACD output ‘F’ open circuit
A8006 ACD output ‘A’ short to earth A8532 ACD output ‘F’ overcurrent
A8007 ACD output ‘A’ open circuit A8602 ACD output ‘G’ error ON
A8032 ACD output ‘A’ overcurrent A8603 ACD output ‘G’ error OFF
A8102 ACD output ‘B’ error ON A8605 ACD output ‘G’ short to battery
A8103 ACD output ‘B’ error OFF A8606 ACD output ‘G’ short to earth
A8105 ACD output ‘B’ short to battery A8607 ACD output ‘G’ open circuit
A8106 ACD output ‘B’ short to earth A8702 ACD output ‘H’ error ON
A8107 ACD output ‘B’ open circuit A8703 ACD output ‘H’ error OFF
A8132 ACD output ‘B’ overcurrent A8705 ACD output ‘H’ short to battery
A8202 ACD output ‘C’ error ON A8706 ACD output ‘H’ short to earth
A8203 ACD output ‘C’ error OFF A8707 ACD output ‘H’ open circuit
A8205 ACD output ‘C’ short to battery
A8206 ACD output ‘C’ short to earth D3905 Left joystick X-axis not in neutral
A8207 ACD output ‘C’ open circuit D3907 Left joystick Y-axis not in neutral
A8232 ACD output ‘C’ overcurrent D4007 Right joystick Y-axis not in neutral
A8302 ACD output ‘D’ error ON D7501 CAN joystick communication error
A8303 ACD output ‘D’ error OFF D7504 No communication from drive controller
A8305 ACD output ‘D’ short to battery D7505 Left joystick X-axis not in neutral
A8306 ACD output ‘D’ short to earth D7507 Left joystick Y-axis not in neutral
A8307 ACD output ‘D’ open circuit D7508 Right joystick Y-axis not in neutral
A8332 ACD output ‘D’ overcurrent D7509 Operating mode switch short to earth or battery
A8402 ACD output ‘E’ error ON D7513 Right front wheel angle sensor unresponsive
A8403 ACD output ‘E’ error OFF D7514 Left front wheel angle sensor unresponsive
A8405 ACD output ‘E’ short to battery D7515 Right rear wheel angle sensor unresponsive
A8406 ACD output ‘E’ short to earth D7516 Left rear wheel angle sensor unresponsive
A8407 ACD output ‘E’ open circuit D7517 Left swash plate not in neutral
A8432 ACD output ‘E’ overcurrent D7518 Right swash plate not in neutral
A8502 ACD output ‘F’ error ON D7519 Left joystick X-axis out of range high
To Next Page
Loading...