BOMANN EHC 3553 - Installation and Electrical Connection; Installation Guidelines; Electrical Connection Requirements; Wiring Diagram and Methods

Installation
InstallationInstallation
Installation
WARNING:
WARNING:WARNING:
WARNING:
The installation
and the connection to the main power
may only be performed by an authorized specialist.
CAUTION
CAUTIONCAUTION
CAUTION:
::
:
• The appliance
must be installed so that heat can
be dissipated. The ventilation openings must not
be blocked.
• Keep a distance
to the appliances back
guarantee a sufficient air circulation.
• Place the appliance only
on a flat, stable, safe
and heat resistant floor.
• The appliance must not
be placed on a socket
• Place the appliance
so that all controls
to reach and
the appliance door can open without
being impeded.
• The appliance can be installed
between two pie
es of furniture with
the same level.
tance between a piece of furniture and the
ance must be at least 30 mm.
•
The distance between the hob and an
hood must be at least as large as
instructions of the extractor hood!
• If the appliance is not horizon
tally
the screw feet
accordingly. Turn clockwise shor
ens the unit base, turning it counterclockwise e
tended it.
Electrical connection
Electrical connectionElectrical connection
Electrical connection
Information for the
Information for the Information for the
Information for the
authorized expert
authorized expertauthorized expert
authorized expert
WARNING:
WARNING:WARNING:
WARNING:
•
The installation to the mains supply must conform
to
the local standards and regulations.
•
Connecting the appliance to a domestic power
socket or using multiple sockets or extension c
bles is not permitted.
•
Improper connection may cause to an
shock
shockshock
shock!
6
and the connection to the main power
may only be performed by an authorized specialist.
must be installed so that heat can
be dissipated. The ventilation openings must not
to the appliances back
in order to
guarantee a sufficient air circulation.
on a flat, stable, safe
be placed on a socket
.
so that all controls
are easily
the appliance door can open without
between two pie
c-
the same level.
The lateral dis-
tance between a piece of furniture and the
appli-
The distance between the hob and an
extractor
hood must be at least as large as
specified in the
instructions of the extractor hood!
tally
leveled, adjust
accordingly. Turn clockwise shor
t-
ens the unit base, turning it counterclockwise e
x-
authorized expert
authorized expertauthorized expert
authorized expert
The installation to the mains supply must conform
the local standards and regulations.
Connecting the appliance to a domestic power
socket or using multiple sockets or extension c
a-
Improper connection may cause to an
electric
electric electric
electric
•
Before connecting, ensure that the power supply
corresponds with the information on the rating l
bel (appliance back)
and the wiring diagram.
•
The appliance is suitable for three
current (400V 3N~50-60
Hz).
•
The appliance can be adjusted for single
current by a respective bypass on the t
block,
based on the circuit diagram below. Select
a suitable cord as mains cable, considering the
connection type and nominal power of the oven.
•
Fix the mains cable in the tension relief.
•
Make sure to connect the protective ground to the
terminal of
the marked terminal block.
•
The electrical installation of the oven should be
equipped with an emergency switch, which
switches off the whole appliance from the mains
supply in an emergency. The distance between
the contacts of the emergency switch must
least 3 mm.
•
Arrange the mains cable in such a way that it
does not get in contact with any hot components
of the appliance. Do not lead it over sharp edges
or corners.
Connection wiring diagram
Connection wiring diagramConnection wiring diagram
Connection wiring diagram
Permissible connection methods
Permissible connection methodsPermissible connection methods
Permissible connection methods
CAUTION:
CAUTION:CAUTION:
CAUTION:
Each
connection requires the protective ground of the
mains to be connected to the
E
As
connecting cable (not supplied)
types are suitable:
- H03VV-F (5G2.5 with three
-
- H05RR-F (5G2.5 with three
-
Before connecting, ensure that the power supply
corresponds with the information on the rating l
a-
and the wiring diagram.
The appliance is suitable for three
-phase and AC
Hz).
The appliance can be adjusted for single
-phase
current by a respective bypass on the t
erminal
based on the circuit diagram below. Select
a suitable cord as mains cable, considering the
connection type and nominal power of the oven.
Fix the mains cable in the tension relief.
Make sure to connect the protective ground to the
the marked terminal block.
The electrical installation of the oven should be
equipped with an emergency switch, which
switches off the whole appliance from the mains
supply in an emergency. The distance between
the contacts of the emergency switch must
be at
Arrange the mains cable in such a way that it
does not get in contact with any hot components
of the appliance. Do not lead it over sharp edges
Permissible connection methods
Permissible connection methodsPermissible connection methods
Permissible connection methods
connection requires the protective ground of the
E
terminal.
connecting cable (not supplied)
the following
-
phase 230/400V 3N~)
-
phase 230/400V 3N~)