Bort BHR-1600-Compact - Page 11

11
THE COMPLETE SET INCLUDES:
1. Adjustable spray nozzle;
2. Pressure hose;
3. Filter.
Product Life:
The service life of the product is 5 years.
Production date:
Is indicated on the packaging of the goods.
Shelf life:
Shelf life is not limited (subject to storage conditions).
Storage conditions:
Products are stored in dry, ventilated warehouses at tem-
peratures from 0 ° C to +40 ° C with a relative humidity of
not more than 80%.
Transportation:
It is strongly prohibited dropping and any mechanical
impact on the packaging during transportation.
When unloading / loading, it is not allowed to use any
type of equipment that works on the principle of pack-
ing clamping.
SERVICE
Have your power tool serviced by a qualied repair per-
son using only identical replacement parts. This will en-
sure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS
When using electric machines always observe the safety
regulations applicable in your country to reduce the risk
of re, electric shock and personal injury. Read the fol-
lowing safety instructions and also the enclosed safety
instructions.
Keep these instructions in a safe place!
Electrical safety
Always check if your mains voltage corresponds with
the value on the type plate.
When replacing old cables or plugs: throw away old
cables or plugs immediately as soon as new ones have
replaced these. It is dangerous to put the plug of a loose
cable into the socket outlet.
When using extension cables:
Only use an approved extension cable that is suitable for
the machine’s power. The cores must have a diameter of
at least 1.5 mm2. When the extension cable is on a reel,
unroll the cable in its entirety.
All electrical connections e.g. extension cable, must be
of an approved waterproof type for outdoor use and
marked accordingly. Extension cables must be threecore,
one of which is EARTH.
Switch o the machine immediately in case of:
14. Malfunction in the mains plug, power cable or dam-
aging of cable.
15. Broken switch.
16. Smoke or stench of scorched insulation.
Specic safety rules
• Do not disconnect the plug by pulling on the electrical
cable.
• If you are too far from the object you wish to clean, do
not move the cleaner nearer by pulling on the high pres-
sure hose; use the handle provided.
• Do not obstruct the ventilation grilles during opera-
tion.
• The cross-section of any extension cables used must
be proportional to their length, i.e. the longer the exten-
sion cable, the greater the cross-section; cables with a
protection level of “IPX5” must be used.
• Position the high pressure cleaner AS NEAR POSSIBLE
to the water supply.
• Use the high pressure cleaner only with accessories
and replacement parts authorized by the manufacturer.
The use of original accessories and replacement parts
will ensure safe, trouble-free operation.
• Avoid unintentional ring of the trigger. Do not carry
the lance / trigger assembly with your hand over the trig-
ger. Always use the trigger lock mechanism.
• Ensure that the safety lock on the trigger is used, when
you have stopped using the pressure washer to prevent
accidental operation.
• Do not use the cleaner with inammable or toxic liq-
uids, or any products which are not compatible with the
correct operation of the high pressure cleaner.
• Do not direct the water jet towards the unit itself, elec-
trical parts or towards other electrical equipment.
• Do not allow children or incompetent persons to use
the high pressure cleaner.
• Do not touch the plug and/or socket with wet hands.
• Do not use the high pressure cleaner if the electrical
cable is damaged.
• Do not use the high pressure cleaner if the high pres-
sure hose is damaged.
• Do not jam the trigger in the operating position.
• Check that the data plates are axed to the high pres-
sure cleaner, if not, inform your dealer. Cleaners without
plates must NOT be used as they are unidentiable and
potentially dangerous.
• Do not tamper with or alter the calibration of the safety
valve.