Bosch 3 611 B64 000 User Manual

INSTANDSETZUNGSHINWEISE
REPAIR INSTRUCTIONS
INSTRUCTIONS DE REPARATION
INSTRUCCIONES DE REPARACION
Änderungen vorbehalten. Unsere Erzeugnisse werden stets
dem neuesten technischen Stand angepaßt. Deshalb behalten
wir uns Änderungen vor.
Bohrhammer
Rotary Hammer
Marteau perforateur
Martillo perforador
Typ 3 611 B64 000 = GBH5-DCE
010
110
Beachten: Instandsetzung, Änderung und Prüfung von Elektrowerkzeugen sind
fachgerecht durchzuführen. Die Sicherheitsvorschriften nach DIN VDE, CEE,AFNOR und
weitere in den einzelnen Ländern gültigen Vorschriften sind einzuhalten.
3 611 B64 000 - D01 (2009-01)
Robert Bosch GmbH
.
PowerTool Devision
.
PT/ASA3
.
70745 Leinfelden-Echterdingen

Bosch 3 611 B64 000 Specifications

General

Impact Energy	3.2 J
Weight	3.5 kg
Drilling Diameter in Concrete	4 – 28 mm
Drilling Diameter in Steel	13 mm
Drilling Diameter in Wood	30 mm
Voltage	230 V
Tool Holder	SDS-plus
No-load Speed	0 - 900 rpm
Impact Rate	0 – 4000 bpm
Power Source	Corded

Summary

Disassembly and Initial Checks

Power Supply Check and Safety Compliance

Perform power supply check and observe safety regulations.

General Disassembly Procedure

Use exploded views and repair instructions for disassembly.

Reassembly Preparation

Step 9: Housing Reassembly

Reassembling the main tool housing with screws.

Steps 10 to 10.3

Reassembly of specific electrical and mechanical parts.

Component Reassembly

Steps 10.4 to 10.6

Reassembly of specific mechanical assemblies.

Steps 11 to 11.2

Reassembly of motor and armature components.

Steps 12 to 12.2

Reassembly of the tool's base and motor housing.

Assembly Procedures

Cleaning and Part Replacement

Clean all parts, replace worn or damaged components with originals.

Step 21: Sealing Surface Preparation

Completely remove oil residue from sealing surfaces.

Steps 21.1 to 21.2

Lubrication and preparation for assembly.

Steps 22 to 22.2

Assembly using auxiliary tools and torque specifications.

Final Assembly Steps

Step 23: Securing Components

Securing the motor using vise jaws and specified torque.

Steps 23.1 to 23.3

Reassembly of internal mechanisms with lubrication.

Step 23.4: Mounting Orientation

Ensure correct mounting orientation for components.

Steps 23.5 to 23.7

Assembly with Loctite, torque, and installation position checks.

Tool Housing and Motor Assembly

Auxiliary Tool for Assembly

Details on using a self-made auxiliary tool for assembly.

Steps 24.1 to 24.2

Steps 24.3 to 24.5

Steps 24.6 to 24.8

Gear and Drive Assembly

Steps 25 to 25.5

Steps 26 to 26.1

Internal Mechanism Assembly

Steps 27 to 27.1

Steps 27.2 to 27.3

Component Reassembly and Checks

Steps 27.4 to 27.6

Steps 27.7 to 27.9

Steps 28 to 28.2

Final Component Assembly

Steps 28.3 to 28.5

Steps 28.6 to 28.7

Steps 28.9 to 28.10

Housing and Switch Assembly

Step 30: Housing Preparation

Steps 30.1 to 30.3

Steps 30.4 to 30.5

Final Testing and Checks

Step 31: High Voltage Test

Perform high voltage test and observe safety regulations.

Step 32: Performance Testing

Conduct test run, impact, electrical, and mechanical checks.

Lubrication and Parts Overview

Lubrication Instructions