Bosch CSG7364B1 User Manual

en Time-setting options
16
10.1 Setting the cooking time
You can set the cooking time for the operation up to
24hours.
Requirement:An operating mode and temperature or
level have been set.
1.
Press ⁠"Cooking time".
2.
To set the cooking time, press the relevant time
value, e.g. hour display "h" or minute display "m".
a The selected value is marked in blue.
3.
Use the setting ring to set the cooking time.
If required, use to reset the setting value.
4.
To confirm the set cooking time, press on the dis-
play.
5.
Press to start the operation.
a The appliance starts to heat and the time counts
down.
a When the time has elapsed, a signal sounds. A
message appears on the display confirming that the
operation has finished.
6.
Once the cooking time has elapsed:
‒ If required, you can select other settings and re-
start the operation.
‒ When the food is ready, use to switch the ap-
pliance off.
Changing the cooking time
You can change the cooking time at any time.
1.
Press on the display.
2.
Press the cooking time ⁠.
3.
Use the setting ring to change the cooking time.
4.
To confirm the change, press on the display.
a The change is applied.
Cancelling the cooking time
You can cancel the cooking time at any time.
1.
Press on the display.
2.
Press the cooking time ⁠.
3.
Reset the cooking time using ⁠.
Note:For operating modes that always require a
cooking time, the appliance resets the cooking time
to the preset value.
4.
To confirm the change, press on the display.
a The change is applied.
10.2 Setting the end time
You can delay the time at which the cooking time for
the operation is due to end by up to 24 hours.
Notes
¡ To achieve good cooking results, do not delay the
time once the operation has already started.
¡ Food will spoil if you leave it in the cooking com-
partment for too long.
Requirements
¡ An operating mode and temperature or level have
been set.
¡ A cooking time is set.
1.
Press ⁠ "End time".
2.
To set the time, press the hour display or the minute
display.
a The selected value is marked in blue.
3.
Use the setting ring to delay the time.
If required, use to reset the setting value.
4.
To confirm the set time, press on the display.
5.
Press to start the operation.
a The display shows the time remaining until the oper-
ation starts. The appliance is in standby mode.
a Once the start time has been reached, the appli-
ance starts heating and the cooking time starts
counting down.
a When the time has elapsed, a signal sounds. A noti-
fication appears on the display confirming that the
operation has finished.
6.
Once the cooking time has elapsed:
‒ If required, you can select other settings and re-
start the operation.
‒ When the food is ready, use to switch the ap-
pliance off.
Changing the end time
To achieve good cooking results, only change the set
time before the operation starts and before the cooking
time starts counting down.
1.
Press to pause the operation.
2.
Press the end time ⁠.
3.
Use the setting ring to change the end time.
4.
To confirm the change, press on the display.
5.
Press to start the operation.
Cancelling the end time
You can delete the set end time at any time.
1.
Press to pause the operation.
2.
Press the end time ⁠.
3.
Use to reset the end time.
Note:For operating modes that always require a
cooking time, the appliance resets the time at which
the cooking time ends to the next possible time.
4.
To confirm the change, press on the display.
5.
Press to start the operation.
10.3 Setting the timer
The timer runs independently during the operation. You
can set the timer for up to 24hours. The timer has its
own signal so that you can tell whether it is the timer or
a cooking time that has elapsed.
Requirement:If the appliance is switched off, press
the display first. The button lights up.
1.
Press ⁠.
2.
To set the timer, press the relevant time value on
the display, e.g. minute display "m" or second dis-
play "s".
a The selected value is marked in blue.
3.
Set the timer using the setting ring.
‒ To fine-tune the setting values, e.g. to set a time
to the precise second, press and hold the corres-
ponding area in the setting ring for around 1-2
seconds. The finely tined setting values are
shown in dots.
‒ If required, use to reset the setting value.
4.
To start the timer, press on the display.
a The timer counts down.
a The timer remains visible on the display if the appli-
ance is switched off.

Bosch CSG7364B1 Specifications

General

Brand	Bosch
Model	CSG7364B1
Category	Oven
Language	English