What to do if my Bosch Iron does not produce any steam?
If the Bosch Iron does not produce any steam, especially during first use, ensure that water has completely filled the hose by pressing and holding the steam release button until steam comes out. Also, if the “Calc'nClean” indicator light is flashing, it means the descaling process hasn't been completed; perform a cleaning cycle as described in the “Descaling process” section.
Why does my Bosch Iron make a pumping sound?
If your Bosch Iron is making a pumping sound, it's usually because water is being pumped into the iron, which is normal. However, also check if the water tank is empty and, if so, refill it.
Why does my Bosch Iron produce little steam?
If your Bosch Iron produces little steam, especially if it has been switched on recently, this is normal. The iron produces steam gradually until it is stabilized.
What to do if dirt comes out through the soleplate of my Bosch Iron?
If dirt comes out through the soleplate of your Bosch Iron, it's likely due to a build-up of lime scale or minerals. Address this by carrying out a cleaning cycle. Also, ensure that you never add chemical products or additives to the water; instead, clean the soleplate with a damp cloth.
What to do if the “Calc'nClean” indicator light (1) does not turn off on my Bosch Iron?
If the “Calc'nClean” indicator light on your Bosch Iron does not turn off, the descaling process was likely interrupted. Restart and complete the descaling process to resolve this issue.
Why does my Bosch Iron smoke when I turn it on?
If your Bosch Iron begins to smoke when switched on for the first time, it's normal. Certain components have been lightly greased at the factory, and this may produce a small amount of smoke when initially heated. This will stop after a short while.
What to do if my Bosch EasyComfort 4 Ironing Centers iron does not produce steam?
If your Bosch Ironing Center is not producing steam, it could be due to a couple of reasons. First, if it's the initial use, the hose might not be completely filled with water. To resolve this, press and hold the steam release button until steam comes out. Alternatively, the 'Calc'nClean' indicator light might be flashing, indicating that the descaling process hasn't been completed. In this case, perform a cleaning cycle as described in the 'Descaling process' section.
Why is dirt coming out of my Bosch EasyComfort 4 iron?
If dirt is coming out through the soleplate of your Bosch Ironing Center, it's likely due to a build-up of lime scale or minerals inside the iron. You should carry out a cleaning cycle. Also, it might be caused by using chemical products or additives in the water tank. Never add products to the water. Clean the soleplate with a damp cloth.
What to do if the 'Calc'nClean' indicator light doesn't turn off on my Bosch EasyComfort 4 Ironing Centers?
If the 'Calc'nClean' indicator light on your Bosch Ironing Center doesn't turn off, it means the iron descaling process was stopped before it finished. You'll need to restart and complete the descaling process to resolve this issue.
Why does my Bosch EasyComfort 4 Ironing Centers make a pumping sound?
If your Bosch Ironing Center is making a pumping sound, there are two possible causes. It's either because water is being pumped into the iron, which is normal, or the water tank is empty, in which case you should fill the water tank.
Read operating instructions carefully and safeguard them for future reference.
Information on how to dispose of the appliance responsibly according to EU directives.
Overview of the components and parts of the appliance.
Discover the benefits of EasyComfort for simple, fast, and safe ironing.
Instructions for filling the water tank with tap water, emphasizing no additives.
Steps to switch on the appliance and indications for heating completion.
Guide to ironing with steam, including tips for efficient use.
Using the special function for tackling difficult creases with powerful steam shots.
How to remove creases from hanging clothes or curtains using steam.
Instructions for using the energy saving setting to conserve energy and water.
Information on the automatic switch-off function for safety and energy saving.
Procedure for removing scale particles indicated by the warning light.
Guidelines for regular cleaning of the appliance and soleplate.
Instructions on how to properly store the iron and its components.
General| Brand | Bosch |
|---|---|
| Model | EasyComfort 4 Series |
| Category | Ironing Centers |
| Language | English |
To Next Page
