What to do if my Bosch Iron does not produce any steam?
If the Bosch Iron does not produce any steam, especially during first use, ensure that water has completely filled the hose by pressing and holding the steam release button until steam comes out. Also, if the “Calc'nClean” indicator light is flashing, it means the descaling process hasn't been completed; perform a cleaning cycle as described in the “Descaling process” section.
Why does my Bosch Iron make a pumping sound?
If your Bosch Iron is making a pumping sound, it's usually because water is being pumped into the iron, which is normal. However, also check if the water tank is empty and, if so, refill it.
Why does my Bosch Iron produce little steam?
If your Bosch Iron produces little steam, especially if it has been switched on recently, this is normal. The iron produces steam gradually until it is stabilized.
What to do if dirt comes out through the soleplate of my Bosch Iron?
If dirt comes out through the soleplate of your Bosch Iron, it's likely due to a build-up of lime scale or minerals. Address this by carrying out a cleaning cycle. Also, ensure that you never add chemical products or additives to the water; instead, clean the soleplate with a damp cloth.
What to do if the “Calc'nClean” indicator light (1) does not turn off on my Bosch Iron?
If the “Calc'nClean” indicator light on your Bosch Iron does not turn off, the descaling process was likely interrupted. Restart and complete the descaling process to resolve this issue.
Why does my Bosch Iron smoke when I turn it on?
If your Bosch Iron begins to smoke when switched on for the first time, it's normal. Certain components have been lightly greased at the factory, and this may produce a small amount of smoke when initially heated. This will stop after a short while.
What to do if my Bosch EasyComfort TDS4050 Ironing Centers iron does not produce steam?
If your Bosch Ironing Center is not producing steam, it could be due to a couple of reasons. First, if it's the initial use, the hose might not be completely filled with water. To resolve this, press and hold the steam release button until steam comes out. Alternatively, the 'Calc'nClean' indicator light might be flashing, indicating that the descaling process hasn't been completed. In this case, perform a cleaning cycle as described in the 'Descaling process' section.
Why is dirt coming out of my Bosch EasyComfort TDS4050 Ironing Centers iron?
If dirt is coming out through the soleplate of your Bosch Ironing Center, it's likely due to a build-up of lime scale or minerals inside the iron. You should carry out a cleaning cycle. Also, it might be caused by using chemical products or additives in the water tank. Never add products to the water. Clean the soleplate with a damp cloth.
What to do if the 'Calc'nClean' indicator light doesn't turn off on my Bosch Ironing Centers?
If the 'Calc'nClean' indicator light on your Bosch Ironing Center doesn't turn off, it means the iron descaling process was stopped before it finished. You'll need to restart and complete the descaling process to resolve this issue.
Why does my Bosch EasyComfort TDS4050 Ironing Centers make a pumping sound?
If your Bosch Ironing Center is making a pumping sound, there are two possible causes. It's either because water is being pumped into the iron, which is normal, or the water tank is empty, in which case you should fill the water tank.
Crucial information and recommendations for proper appliance usage and care.
Information on how to dispose of the appliance responsibly according to EU directives.
Detailed list and explanation of the appliance's components and their functions.
Overview of the EasyComfort ironing system and its benefits for faster, safer ironing.
Instructions on how to safely and correctly fill the water tank with tap water.
Procedure for switching on the appliance and waiting for it to heat up.
Guidance on the most efficient way to iron with steam, including tips for fabric care.
Explanation of the special function for tackling difficult creases with powerful steam shots.
How to use the appliance to remove creases from hanging clothes or curtains.
Details on activating the energy-saving mode and tips for reducing consumption.
Information about the automatic shut-off function for safety and energy conservation.
Step-by-step guide for performing the automatic descaling process to maintain performance.
Instructions for cleaning the appliance's exterior and soleplate safely and effectively.
Guidance on how to properly store the iron and its accessories after use.
General| Model | TDS4050 |
|---|---|
| Brand | Bosch |
| Series | EasyComfort |
| Power | 2400 W |
| Steam output | 120 g/min |
| Water tank capacity | 1.4 L |
| Cord length | 1.9 m |
| Vertical steam | Yes |
| Calc-clean indicator | Yes |
| Anti-scale system | Yes |
| Auto shut-off | Yes |
| Self-Cleaning Function | Yes |
| Soleplate material | Ceramic |
To Next Page
