6 | English
1 609 92A 3L2 | (5.12.16) Bosch Power Tools
sion. Penetrating a water line causes property damage or
may cause an electric shock.
Do not operate the power tool stationary. It is not de-
signed for operation with a saw table.
Do not use high speed steel (HSS) saw blades. Such saw
blades can easily break.
Do not saw ferrous metals. Red hot chips can ignite the
dust extraction.
When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for lengthways and crossways cut-
ting of wood with straight cutting lines as well as mitre cuts in
wood while resting firmly on the workpiece. With suitable saw
blades, thin-walled non-ferrous metals, e. g., profiles, can al-
so be sawed.
Working ferrous metals is not permitted.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 On/Off switch
2 Lock-off button for On/Off switch
3 Spindle lock button (PKS 1500)
4 Auxiliary handle (insulated gripping surface)
5 Scale for mitre angle
6 Wing bolt for parallel guide*
7 Wing bolt for bevel-angle preselection
8 Cutting mark, 45°
9 Cutting mark, 0°
10 Parallel guide*
11 Retracting blade guard
12 Base plate
13 Lever for retracting blade guard
14 Blade guard
15 Handle (insulated gripping surface)
16 Saw spindle
17 Mounting flange
18 Saw blade*
19 Clamping flange
20 Clamping bolt with washer
21 Ring spanner
22 Clamping lever for cutting-depth preselection
23 Set of screw clamps*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Circular Saw PKS 184 PKS 1500
Article number
3 603 C2A 040 3 603 C2A 140
Rated power input
W15001500
No-load speed
min
-1
5300 5300
Cutting depth, max.
–for 0° bevel angle
–for 45° bevel angle
mm
mm
62
49
62
49
Spindle lock –
Base plate dimensions
mm 152 x 271 152 x 271
Saw blade diameter, max.
mm 184 184
Saw blade diameter, min.
mm 184 184
Blade thickness, max.
mm 1.8 1.8
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
OBJ_BUCH-1089-003.book Page 6 Monday, December 5, 2016 3:27 PM
To Next Page
Loading...
