Bosch PMF 220 CE - Page 17

Working without the Auxiliary Handle
Total vibration values a
h
(triax vector sum) and uncertainty K
determined according to EN62841‑2‑4(Sanding),
EN62841‑2‑11(Cutting):
Sanding: a
h
=10 m/s
2
, K=1.5 m/s
2
,
Cutting with plunge cut saw blade: a
h
=16 m/s
2
, K=2 m/s
2
,
Cutting with segmential saw blade: a
h
=14 m/s
2
, K=3 m/s
2
,
Scraping: a
h
=12 m/s
2
, K=1.5 m/s
2
.
Working with the auxiliary handle
Total vibration values a
h
(triax vector sum) and uncertainty K
determined according to EN62841‑2‑4(Sanding),
EN62841‑2‑11(Cutting):
Sanding: a
h
=9 m/s
2
, K=1.5 m/s
2
,
Cutting with plunge cut saw blade: a
h
=17 m/s
2
, K=2 m/s
2
,
Cutting with segmential saw blade: a
h
=18.5 m/s
2
, K=3 m/s
2
,
Scraping: a
h
=16 m/s
2
, K=1.5 m/s
2
.
The vibration level and noise emission value given in these in-
structions have been measured in accordance with a stand-
ardised measuring procedure detailed in EN 62841 and may
be used to compare power tools. They may also be used for a
preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Fitting
u Pull the plug out of the socket before carrying out any
work on the power tool.
Changing the tool
u Wear protective gloves when changing tools. There is
a risk of injury when touching the application tools.
Selecting an Application Tool
Please observe the application tools intended for your power
tool.
Application tool PMF 220 CE
PMF 2000 CE
The following table shows examples of application tools. You can find additional application tools in Bosch’s extensive range of
accessories.
Application tool Material Application
Bi-metal segment
saw blade
Wood-based materials,
plastic, non-ferrous
metals
Separating cuts and plunge saw cuts;
including sawing close to edges, in corners and in difficult-
to-reach areas;
example: Shortening skirting boards that are already in-
stalled or door frames, plunge cuts when adapting floor
panels
Sanding plate for
Delta series 93mm
sanding sheets
Depends on the sanding
sheet
Sanding surfaces at edges, in corners or in difficult-to-
reach areas;
depending on the sanding sheet, e.g. for sanding wood,
paint, varnish, stone;
fleeces for cleaning and for texturing wood, removing rust
from metal and for keying varnish, polishing felt for pre-
polishing
Profile sander Wood, pipes/profiles,
paint, varnish, filler, metal
Convenient and efficient sanding of profiles up to a dia-
meter of 55mm;
red sanding sheets for sanding wood, pipes/profiles, var-
nish, filler and metal
Bi-metal plunge cut
saw blade for wood
and metal
Softwood, soft plastics,
plasterboard, thin-walled
aluminium profiles and
non-ferrous metal pro-
files, thin sheet metal,
Small separating cuts and plunge cuts;
example: Cutting a recess for sockets, cutting a copper
pipe so that it is flush with a surface, making plunge cuts in
plasterboard
English | 17
Bosch Power Tools 1 609 92A 4BL | (01.10.2018)