Why is the water not draining from my Bosch Washer/Dryer?
If the water isn't draining from your Bosch Washer/Dryer, check if the drain pipe or water outlet hose is blocked and clean them if necessary. Also, make sure the drain pipe and water drain hose are not kinked or trapped.
What to do if my Bosch WNC25410GB Washer/Dryer shows error code E:30 / -10?
If your Bosch Washer/Dryer displays error code E:30 / -10, it could be due to several reasons. The water pressure may be low. Also, the filter in the water inflow may be blocked, clean the water inflow filter. Ensure that the tap is turned on. Also, make sure that the water inlet hose is not kinked or jammed.
What does error code E:35 / -10 mean on my Bosch WNC25410GB Washer/Dryer?
If your Bosch Washer/Dryer displays error code E:35 / -10, it indicates there is water in the base trough. Turn off the water tap. It could also mean that the appliance is leaking, in which case you should call the after-sales service.
What does error code E:10 / -00 / -10 / -20 mean on my Bosch WNC25410GB?
If your Bosch Washer/Dryer displays error code E:10 / -00 / -10 / -20, it indicates that the pump for the intelligent dosing system is blocked. Put the appliance into standby mode, clean the pump unit, and then switch the appliance back on. If the display appears again after cleaning the pump unit, or the program cannot be started, call customer service.
Why is the spin result of my Bosch WNC25410GB not satisfactory?
If the spin result of your Bosch Washer/Dryer is not satisfactory, it may be because a low spin speed was selected. Next time you run a wash cycle, set a higher spin speed. Also, the unbalance load detection system may be using a reduced spin speed to eliminate an unbalance; redistribute the laundry in the drum.
What does H:32 mean on my Bosch WNC25410GB and how to fix it?
If your Bosch Washer/Dryer displays H:32, the unbalanced load detection system has interrupted the spin cycle because the laundry is unevenly distributed. To solve this, redistribute the laundry in the drum.
Why is the drying time too long on my Bosch Washer/Dryer?
If the drying time on your Bosch Washer/Dryer is too long, it could be because the ambient temperature is greater than 30 °C. Also, ensure sufficient air circulation at the appliance's installation location by ventilating the area. Furthermore, fluff may have accumulated in the drum, run the Cottons 90°C program without any laundry or detergent.
How to prevent creasing when using my Bosch WNC25410GB?
If you're experiencing creasing with your Bosch Washer/Dryer, the load might be too large. Remove the laundry from the drum as soon as the drying program has finished. Also, ensure you're using a suitable program for the type of fabric you're drying; set the appropriate program.
Why is there detergent residue on the dry laundry from my Bosch Washer/Dryer?
If you notice detergent residue on the dry laundry from your Bosch Washer/Dryer, it may be due to unsuitable detergent added to the dispenser of the intelligent dosing system. Check whether the detergent used is suitable, drain the dispenser, clean it, and then refill it. Also, if intelligent dosing is activated, the basic dosage may not be adjusted, reduce the basic dosage.
What to do if the door of my Bosch WNC25410GB cannot be opened?
If the door of your Bosch Washer/Dryer won't open, it might be due to several reasons. First, the temperature inside might be too high; wait for it to cool down. Second, the water level could be too high; select a suitable program for draining. Finally, there might be a power failure; in this case, use the emergency release to open the door.
General| Model Number | WNC25410GB |
|---|---|
| Appliance placement | Freestanding |
| Energy Efficiency Class (Wash) | A |
| Built-in display | Yes |
| Door hinge | Left |
| Spin-drying class | B |
| Washing class | A |
| Drum Material | Stainless steel |
| Type | Washer dryer |
| Loading type | Front-loading |
| Dimensions (H x W x D) | 848 x 598 x 590 mm |
| Programs | Delicates |
To Next Page
