To Next PageTo Next Page
Need help?Do you have a question about the Boss GT-10 and is the answer not in the manual?
General| Type | Multi-Effects Processor |
|---|---|
| Amp Modeling | Yes |
| D/A Conversion | 24-bit |
| Sampling Frequency | 44.1 kHz |
| Expression Pedal | Yes, built-in |
| Outputs | 2 x 1/4" (L/Mono, R) |
| MIDI I/O | In, Out |
| A/D Conversion | 24-bit |
| Effects Types | Overdrive, Distortion, Delay, Reverb, Modulation |
Explains the meaning of warning symbols used in the manual for user safety.
Provides a list of crucial safety instructions and precautions for operating the unit.
Details on connecting and using the unit's power supply safely.
Guidelines for positioning the unit to ensure proper operation and prevent damage.
Instructions for cleaning and maintaining the unit's condition.
Information regarding data loss during repairs and service recommendations.
General safety advice and precautions for using the unit.
Highlights the advanced COSM effects technology for natural sound and expressiveness.
Describes the EZ TONE feature for intuitive sound creation using graphical interfaces.
Explains the Phrase Loop function for recording and overdubbing performances.
Details the Parallel Chain function for creating independent effect chains.
Compares the unit's operation to compact effects processors for ease of use.
Notes the use of bright LED indicators for clear visibility in any environment.
Identifies and describes the controls and displays on the front of the GT-10.
Identifies and describes the input/output jacks and connectors on the rear panel.
Provides initial setup steps including connections and power.
Instructions for adjusting the output volume level using the OUTPUT LEVEL knob.
Explains how to access and use the built-in guitar tuner.
Guides users on selecting and playing sounds (patches) on the GT-10.
Describes how to use the dial for switching between patches.
Explains how to use pedals like EXP and CTL for effect control.
Covers fundamental operations for editing sound settings.
Guide to creating new sounds by modifying existing patches.
Details how to turn individual effects within a patch on or off.
Explains how to fine-tune effect parameters for desired sound.
Describes the EZ TONE feature for easy sound creation based on musical genre.
Guides on matching settings to guitar pickups and output devices.
Instructions for selecting basic tones and variations within EZ TONE.
Details on adjusting distortion levels using the Tone Grid.
Guidance on adjusting various effects parameters using the Tone Grid.
Step-by-step guide for connecting the GT-10 to guitars, amps, and other devices.
Provides the correct sequence for powering on the GT-10 and connected equipment.
Explains the various icons displayed on the GT-10's Play screen.
Details how to switch between different Play screen variations.
Instructions for setting the overall output volume using the OUTPUT LEVEL knob.
Explains how to activate and deactivate the guitar tuner function.
Describes the information shown on the display while tuning.
Step-by-step guide on how to tune a guitar using the built-in tuner.
Instructions for adjusting the reference pitch for tuning.
Details how to set the tuner output mode (Bypass/Mute).
Explains assigning tuner control to CTL pedals.
Describes assigning tuner control to the EXP Pedal switch.
Explains assigning tuner control to Number Pedals.
Defines what a patch is and how they are stored in memory.
Guides on selecting patches using the BANK and Number pedals.
Instructions for selecting patches within the current bank.
Instructions for selecting patches from different banks.
Introduction to the EZ TONE feature for simplified sound creation.
Detailed steps for creating a specific sound using EZ TONE CREATE.
Guide to fine-tuning sounds using the EZ TONE EDIT function.
Explains how to switch individual effects on or off using button controls.
Describes using parameter knobs for switching effects on/off.
Guide to using preset 'Quick Settings' for easily creating new effect sounds.
Explains how to switch display modes for effect settings.
Details on selecting the TYPE parameter for OD/DS and PREAMP effects.
Instructions for adjusting the Graphic EQ settings for FX-1 and FX-2.
Explains how to check effect output levels using the FX CHAIN level meter.
Detailed procedure for saving edited patch settings to memory.
Instructions for copying Preset or User patches to other User patch locations.
Guides on assigning functions to the PARAMETER knobs in the Play screen.
Explains how to assign functions to CTL, EXP pedals, and switches.
Details setting global functions for CTL/EXP pedals and switches.
Guides on setting CTL/EXP functions for each patch independently.
Describes using preset Quick Settings for EXP Pedal functions.
Explains assigning controller functions to individual patches using Assign numbers.
Information on using preset settings to simplify parameter adjustments.
Details on manually assigning controllers to specific parameters.
Explains how parameter values change within defined ranges.
Describes setting the operational range for controller inputs.
Explains the Internal Pedal system for automatic parameter changes.
Guides on controlling effects in Manual Mode using BANK/Number pedals.
Instructions on how to enable and enter Manual Mode.
Details on using pedals to switch assigned effects in Manual Mode.
Overview of assignable functions for effect switches on pedals.
Step-by-step guide to assigning effect on/off functions to pedals.
Explains how to use Number Pedals for various functions like tuner and preamp switching.
Covers recording, overdubbing, and playing phrases with the Phrase Loop feature.
Provides a basic explanation of the Phrase Loop functionality.
Detailed guide on how to use the Phrase Loop feature for recording and playback.
Instructions for recording a phrase loop.
Guide to adding new sounds by overdubbing onto an existing phrase loop.
Explains how to delete recorded phrases from the Phrase Loop.
Details on configuring Phrase Loop parameters like Mode and Pedal Mode.
Summarizes the operational flow of the Phrase Loop feature.
Guides on adjusting input settings to match different guitars.
Explains the Global function for adjusting overall tone across all patches.
Details on adjusting the global equalizer settings.
Describes setting the global threshold for the noise suppressor.
Explains how to control the global reverb level.
Guides on setting the output reference level for connected equipment.
Instructions for adjusting the audio signal level from the DIGITAL OUT jack.
Details on adjusting the LCD display contrast for better readability.
Explains the Patch Change Mode for effect carry-over between patches.
Describes setting a single preamp globally for all patches.
Guides on using system-wide preamp settings.
Instructions for saving current preamp settings as system settings.
Detailed procedure for saving preamp settings to the system.
Explains how to set limits on the range of switchable banks.
Details on setting the timing for patch switching when changing banks.
Explains how EXP Pedal values are retained when switching patches.
Describes options for pedal indicator lighting behavior.
Explains how to set the dial's function for patch switching or value adjustment.
Guide to resetting the unit's settings to factory defaults.
Procedure for recalibrating the EXP Pedal for optimal operation.
Overview of MIDI capabilities and operations with the GT-10.
Details on how the GT-10 can control external MIDI devices.
Explains how the GT-10 sends Program Change messages for patch switching.
Describes sending Control Change messages for parameter control.
Information on transmitting data (settings) using Exclusive messages.
Guides on controlling the GT-10 from an external MIDI device.
Explains how to switch patches via MIDI Program Change messages.
Describes receiving Control Change messages to control GT-10 parameters.
Information on restoring data from MIDI sequencers or other devices.
Details on MIDI communication between the GT-10 and a computer via USB.
Guide to configuring various MIDI functions on the GT-10.
Instructions for setting the MIDI channel for receiving messages.
Explains how to configure the MIDI Omni Mode setting.
Instructions for setting the MIDI channel for transmitting messages.
Details on setting the MIDI Device ID for transmitting/receiving Exclusive messages.
Explains how to set the basis for synchronizing timing with MIDI Clock.
Guides on configuring the output of Program Change messages.
Details on sending EXP Pedal data as Control Change messages.
Explains sending EXP Pedal SW data as Control Change messages.
Guides on sending external EXP Pedal data as Control Change messages.
Details on sending CTL Pedal data as Control Change messages.
Explains sending external footswitch data as Control Change messages.
Guides on mapping Program Change messages to patches.
Explains how to enable or disable Program Change Map settings.
Instructions for configuring the Program Change Map.
Details on changing patches using Bank Select and Program Change messages.
Explains how to change external MIDI device patch numbers from the GT-10.
Guides on changing GT-10 patch numbers from an external MIDI device.
Procedure for transmitting settings to MIDI sequencers or other GT-10s.
Diagrams for connecting MIDI devices for bulk dump transmission.
Details on initiating the bulk dump transmission process.
Procedure for restoring settings from MIDI data via bulk load.
Diagrams for connecting MIDI devices for bulk load reception.
Details on initiating the bulk load reception process.
Preparation steps before connecting the GT-10 to a computer via USB.
Guide to installing and configuring the necessary USB driver.
Details on transferring MIDI messages between computer and GT-10 via USB.
Explanation of the role and function of a USB driver.
Instructions on switching between Standard and Advanced driver modes.
Guides on configuring various USB-related functions.
Details on adjusting digital audio signal levels for USB input/output.
Explains how to route GT-10 sound to OUTPUT and PHONES jacks.
Describes controlling Direct Monitor settings remotely.
Guides on recording the GT-10's output to a computer.
Instructions for applying GT-10 effects to computer audio playback.
Detailed parameters for the Compressor effect.
Detailed parameters for the Overdrive/Distortion effect.
Settings available when the TYPE parameter is set to Custom.
Detailed parameters for the Preamp section, including channel modes and types.
Lists and describes the available preamp types for simulation.
Parameter for adjusting the amp's distortion level.
Parameter for adjusting the low-frequency tone.
Parameter for adjusting the middle-frequency tone.
Parameter for adjusting the high-frequency tone.
Parameter for adjusting the ultra-high frequency tone.
Parameter for adjusting the overall preamp volume.
Parameter to turn the bright setting on or off.
Parameter for selecting distortion levels (Low, Middle, High).
Parameter to enable or disable the solo tone.
Parameter for setting the volume level when Solo Sw is ON.
Parameter for selecting the speaker type for simulation.
Detailed parameters for the Equalizer effect.
Parameter to turn the EQ effect on or off.
Parameter to set the frequency for the low cut filter.
Parameter to adjust the low frequency range tone.
Parameter to specify the center frequency for low-middle EQ.
Parameter to adjust the width of the low-middle EQ area.
Parameter to adjust the low-middle frequency range tone.
Parameter to specify the center frequency for high-middle EQ.
Parameter to adjust the width of the high-middle EQ area.
Parameter to adjust the high-middle frequency range tone.
Parameter to adjust the high frequency range tone.
Parameter to set the frequency for the high cut filter.
Parameter to adjust the overall equalizer volume.
Details on parameters for FX-1 and FX-2 effect slots.
Parameter to select the effect to be used in FX-1 or FX-2.
Detailed parameters for the Touch Wah effect.
Parameter to select the wah mode (LPF or BPF).
Parameter to select the wah filter direction (Up or Down).
Parameter to adjust wah sensitivity to input level.
Parameter to adjust the center frequency of the wah effect.
Parameter to adjust wah effect amount around center frequency.
Parameter to adjust the volume of the wah effect sound.
Parameter to adjust the volume of the direct sound.
Detailed parameters for the Auto Wah effect.
Detailed parameters for the Sub Wah effect.
Detailed parameters for the Advanced Compressor effect.
Detailed parameters for the Limiter effect.
Detailed parameters for the Graphic Equalizer effect.
Detailed parameters for the Parametric EQ effect.
Detailed parameters for the Tone Modify effect.
Detailed parameters for the Guitar Simulator effect.
Detailed parameters for the Slow Gear effect.
Detailed parameters for the Defretter effect.
Detailed parameters for the Wave Synth effect.
Detailed parameters for the Guitar Synth effect.
Detailed parameters for the Sitar Simulator effect.
Detailed parameters for the Octave effect.
Detailed parameters for the Pitch Shifter effect.
Detailed parameters for the Harmonist effect.
Instructions for creating custom harmony scales.
Detailed parameters for the Auto Riff function.
Guide to creating original phrases for the Auto Riff function.
Detailed parameters for the Sound Hold effect.
Detailed parameters for the Acoustic Processor effect.
Detailed parameters for the Feedbacker effect.
Detailed parameters for the Anti-Feedback effect.
Detailed parameters for the Phaser effect.
Detailed parameters for the Flanger effect.
Detailed parameters for the Tremolo effect.
Detailed parameters for the Rotary effect.
Detailed parameters for the Uni-V effect.
Detailed parameters for the Pan effect.
Detailed parameters for the Slicer effect.
Detailed parameters for the Vibrato effect.
Detailed parameters for the Ring Modulator effect.
Detailed parameters for the Humanizer effect.
Detailed parameters for the 2x2 Chorus effect.
Detailed parameters for the Sub Delay effect.
Detailed parameters for the Delay effect.
Parameter to turn the Delay effect on or off.
Parameter to select the type of delay effect.
Common parameters applicable to various delay types.
Parameter for adjusting the pan of the left channel delay.
Parameters specific to Dual-S, Dual-P, and Dual-L/R delay types.
Detailed parameters for the Warp effect.
Detailed parameters for the Modulate effect on delay.
Detailed parameters for the Chorus effect.
Detailed parameters for the Reverb effect.
Global settings for master volume, EQ, and other overall sound adjustments.
Parameters for setting Master BPM and Master Key.
Parameters related to Pedal FX assignments and functions.
Details on assigning functions to switches and pedals.
Detailed parameters for the Wah effect.
Detailed parameters for the Pedal Bend effect.
Detailed parameters for the Foot Volume effect.
Lists parameters controllable via pedals and switches.
Comprehensive guide to assigning functions to controllers via ASSIGN 1-8.
Parameter to enable or disable the ASSIGN 1-8 functions.
Parameter to select the target parameter for assignment.
Sets the minimum value for the assignment range.
Sets the maximum value for the assignment range.
Parameter to select the controller assigned to the function.
Determines the behavior of the controller switch (Momentary or Toggle).
Sets the lower limit of the controllable range for target parameters.
Sets the upper limit of the controllable range for target parameters.
Parameter to set the trigger for the internal pedal.
Parameter to control the time for the assumed EXP Pedal movement.
Parameter to select the curve type for assumed expression pedal changes.
Parameter to determine the time for one cycle of the assumed EXP Pedal.
Lists parameters that can be targeted for controller assignments.
Target parameters available for the Compressor effect.
Target parameters available for the OD/DS effect.
Target parameters available for the Preamp section.
Target parameters available for the EQ effect.
Target parameters available for FX-1 and FX-2 effects.
Target parameters for the Wave Synth effect.
Target parameters for the Guitar Synth effect.
Target parameters for the Sitar Simulator effect.
Target parameters for the Octave effect.
Target parameters for the Pitch Shifter effect.
Target parameters for the Harmonist effect.
Target parameters for the Auto Riff function.
Target parameters for the Sound Hold effect.
Target parameters for the Acoustic Processor effect.
Target parameters for the Feedbacker effect.
Target parameters for the Anti-Feedback effect.
Target parameters for the Phaser effect.
Target parameters for the Flanger effect.
Target parameters for the Tremolo effect.
Target parameters for the Rotary effect.
Target parameters for the Uni-V effect.
Target parameters for the Pan effect.
Target parameters for the Slicer effect.
Target parameters for the Vibrato effect.
Target parameters for the Ring Modulator effect.
Target parameters for the Humanizer effect.
Target parameters for the 2x2 Chorus effect.
Target parameters for the Sub Delay effect.
Target parameters for the Delay effect.
Target parameters for the Chorus effect.
Target parameters for the Reverb effect.
Target parameters for Master settings.
Target parameters for Master BPM and Key.
Target parameters for Amp Control settings.
Target parameters for Pedal assignments.
Target parameters for Send/Return settings.
Target parameters for Noise Suppressor settings.
Target parameters for miscellaneous functions.
Detailed explanation of SEND/RETURN functionality and modes.
Detailed explanation of Amp Control functionality.
Detailed parameters for the Noise Suppressor effect.
Detailed explanation of the EZ TONE feature.
First step in EZ TONE: setting pickup and output device.
Second step in EZ TONE: selecting basic tones and variations.
Third step in EZ TONE: adjusting distortion levels.
Fourth step in EZ TONE: selecting and adjusting effects.
System-wide settings for the GT-10's operating environment.
System settings related to the tuner function.
System settings for input and output levels and configurations.
System settings for global equalization.
System settings for noise suppressor and reverb levels.
System settings for the Phrase Loop feature.
Parameter to set the mode for Phrase Loop (Performance/Patch Edit).
Parameter to set how BANK pedals control Phrase Loop.
Parameter to select recording mode (Mono/Stereo).
Parameter to set the playback volume of the phrase loop.
Parameter to configure the clear function for the phrase loop pedal.
Settings for controlling effects manually using pedals.
System settings related to patch switching and pedal behavior.
Parameter to select patch-specific or system-wide preamp settings.
Parameter to control effect carry-over during patch changes.
Parameter to set the timing for bank switching.
Parameter to set the minimum bank for switching.
Parameter to set the maximum bank for switching.
Parameter to determine if EXP Pedal values are carried over between patches.
Parameter to adjust how unlit pedal indicators behave.
Parameter to assign functions to Number Pedals.
Parameter to set the dial's function for patch or value changes.
Settings for configuring controllers like knobs and pedals.
Details on assigning functions to system knobs (P1-P4).
Settings for EXP Pedal 1 and EXP Pedal 2.
Settings for the EXP Pedal Switch function.
Settings for CTL pedals 1 through 4.
Reference chart for parameter names displayed with system knobs.
Settings related to the LCD display contrast.
Comprehensive settings for MIDI communication.
Parameter to set the MIDI channel for receiving messages.
Parameter to configure MIDI Omni Mode (On/Off).
Parameter to set the MIDI channel for transmitting messages.
Parameter to set the MIDI Device ID for Exclusive messages.
Parameter to set the basis for timing synchronization with MIDI Clock.
Parameter to configure Program Change message output.
Sets controller numbers for Control Change messages.
Parameter to switch between default and Program Change Map settings.
Guides on mapping Program Change messages to patches.
Instructions for transmitting settings via Bulk Dump.
Settings related to USB connectivity.
Parameter to select between Standard and Advanced USB driver modes.
Parameter to enable/disable external control of Direct Monitor.
Setting for routing GT-10 sound to output jacks.
Parameter to select the type of connected output device.
Selects whether to use patch-specific or system-wide output settings.
Specifies the connected device type for output settings.
Supplementary information including signal flow and charts.
Diagram illustrating the signal path through the GT-10.
Chart detailing MIDI messages transmitted and recognized by the GT-10.
Technical specifications of the GT-10 hardware.
List of included accessories with the GT-10.
List of optional accessories available for the GT-10.
Information on error messages and how to resolve them.
Guides users through common problems and their solutions.
Troubleshooting steps for issues related to sound output.
Troubleshooting steps for no sound or low volume issues.
Troubleshooting steps for unexpected oscillating sound.
Troubleshooting steps when preamp tone doesn't change between patches.
Troubleshooting steps for issues with parameter knob or dial control.
Troubleshooting steps when patches fail to change.
Troubleshooting steps when assigned parameters are not controllable.
Troubleshooting steps for MIDI communication issues.
