Bradford White TTW URG2PV75H6N User Manual (English)

Questions and Answers:

R
Robert SmithAug 19, 2025
Why is my Bradford White Water Heater showing six flashes then two flashes, with a three second pause (Soft lockout)?
- N
  Nicole LeachAug 19, 2025
  If your Bradford White Water Heater shows six flashes followed by two flashes, with a three-second pause (Soft lockout), it may be due to kinked or blocked pressure switch tubing, a vent blockage or improper vent configuration, the vent termination being affected by windy conditions, the blower not spinning up to speed, the vent temperature being too high or a faulty pressure switch or blower temperature switch. Resolve any issues with the pressure switch tubing and ensure the blower and vent configurations are correct.
P
pwaltersAug 21, 2025
What should I do if my Bradford White Water Heater shows seven flashes with a three-second pause?
- J
  John ScottAug 21, 2025
  If your Bradford White Water Heater displays seven flashes followed by a three-second pause, this could be due to flammable vapor being present, the flammable vapor sensor being exposed to excessive moisture or extreme ambient temperatures, or a simulated resistive device being removed or out of range (if applicable). Ensure the area is free of flammable vapors and that the sensor is not exposed to extreme conditions.
K
Kelli CarrollAug 23, 2025
What to do if my Bradford White TTW URG2PV75H6N Water Heater shows three flashes with a three-second pause?
- R
  Robert MunozAug 23, 2025
  If your Bradford White Water Heater is showing three flashes with a three-second pause, inspect for any vent blockages and make sure the blower is operating properly. The issue might be caused by a vent blockage, an improper vent configuration, kinked or blocked pressure switch tubing, the blower not spinning up to speed, the vent temperature being too high, or a faulty pressure switch or vent limit switch.
K
Karen KhanAug 26, 2025
What does it mean if my Bradford White TTW URG2PV75H6N Water Heater is flashing four times with a three-second pause?
- T
  Timothy HodgesAug 26, 2025
  If your Bradford White Water Heater displays four flashes followed by a three-second pause, it could be due to excessive sediment buildup, hot water entering the tank from another source in the potable loop, or a faulty gas valve. You should remove any sediment buildup and check for other hot water sources affecting the tank.
K
Kelly SchmidtAug 28, 2025
What does it mean when my Bradford White TTW URG2PV75H6N flashes twice with a three second pause?
- A
  Amy MooreAug 28, 2025
  If your Bradford White Water Heater is showing two flashes, followed by a three-second pause, the issue could stem from kinked or blocked pressure switch tubing, a blocked pressure tap on the switch, or a faulty pressure switch. You should check and clear the pressure switch tubing and verify the switch function.
D
david93Aug 30, 2025
Why is my Bradford White TTW URG2PV75H6N Water Heater showing six flashes then three flashes, with a three second pause (Soft lockout)?
- M
  Maria HullAug 30, 2025
  If your Bradford White Water Heater is showing six flashes followed by three flashes, with a three-second pause (Soft lockout), it could be caused by an unstable pilot, a blocked or restricted pilot tube, oxidation buildup on the pilot electrode, wire damage to the pilot assembly or a bad connection at the gas valve, or insufficient combustion air. Investigate potential causes, including blockages and insufficient air supply.
J
Jason TorresSep 1, 2025
Why is my Bradford White Water Heater showing six flashes then four flashes, with a three second pause (Soft lockout)?
- D
  David SchwartzSep 1, 2025
  If your Bradford White Water Heater shows six flashes followed by four flashes, with a three-second pause (Soft lockout), this indicates the pilot valve is stuck in open position. Repair or replace the pilot valve.
J
Joyce PerezSep 3, 2025
What does it mean when my Bradford White TTW URG2PV75H6N flashes eight times then two flashes, with a three second pause?
- M
  Martha MorrisonSep 3, 2025
  If your Bradford White Water Heater displays eight flashes followed by two flashes, with a three-second pause, this may indicate damage to the sensor or wire in the control’s well, the control’s sensor resistance is out of range or you have to replace the control. Inspect and replace the damaged sensor or wire.
K
Kelly BlanchardSep 5, 2025
What does it mean when my Bradford White Water Heater flashes eight times then one flash, with a three second pause?
- T
  Tracey MillerSep 6, 2025
  If your Bradford White Water Heater displays eight flashes followed by one flash, with a three-second pause, this could mean the flammable vapor sensor is out of specification or there is a possible short. Check the flammable vapor sensor for specification compliance and rectify any short.
S
Scott FordSep 7, 2025
What should I do if my Bradford White TTW URG2PV75H6N is showing eight flashes then three flashes, with a three second pause?
- A
  Alicia BrownSep 7, 2025
  If your Bradford White Water Heater is showing eight flashes followed by three flashes, with a three-second pause, verify the control is not wet or physically damaged. Reset the control on/off switch. If the 8?3 error persists, replace the electronic module as necessary.