To Next PageTo Next PageWhat to do if my Brandt Ventilation Hood is not operating effectively?
If your Brandt Ventilation Hood isn't operating effectively, make sure that: * The selected motor speed is high enough for the amount of smoke and vapors. * Your kitchen has enough ventilation for fresh air to come in. * The carbon filter isn't worn out, especially if the hood is in recycling mode.
What to do if my Brandt Ventilation Hood stopped working?
If your Brandt Ventilation Hood stopped working, check that: * The power is on. * The single-pole cut-off device hasn't been activated.
Instructions available online. Heed advice for safety and protection of others during installation and use.
Appliance for home use only. Not for commercial/industrial use. Children under 8 and persons with reduced capacities require supervision.
Disconnect power before touching terminals. Damaged power cord must be replaced by manufacturer or qualified person to avoid danger.
Obey air evacuation regulations. Air must not go into gas/fuel appliance ducts. Ensure room ventilation when using hood with gas appliances.
Do not flambé or turn on uncovered gas rings. Monitor fryers. Clean filters regularly to prevent grease buildup and fire hazards.
Appliance packaging is recyclable. Contact local authorities for disposal points. Thank you for helping protect the environment.
Diagram illustrating the cooker hood's dimensions, including height adjustments and width/depth specifications for installation.
Connect hood to external outlet via flue (min Ø 125mm). If flue is smaller, use recycling mode. Ensure safe distance from cooking hob.
For homes without external outlets. Requires an active carbon filter to absorb odours. See Chapter 4 for filter replacement instructions.
Ensure adequate voltage and good wire condition. Connect to accessible socket. Use 10 or 16A fuse. Consult electrician for installation changes.
Install hood respecting ventilation rules and minimum distance. Mark wall, drill holes, fix support, attach sleeve, and secure hood body.
Instructions for fixing the duct support U-bracket and attaching ventilation ducts and sleeves to the hood and ceiling.
Steps for connecting the hood to an external duct, including securing brackets, ducts, and making electrical connections for optimal airflow.
Details on fitting duct support, sleeve adapter, deflector, and ducts for recycling mode. Includes tips for optimal use and warnings.
Explains the function of each push button (stop, speed settings, light) and provides a diagram of the control panel for user reference.
Clean filter cartridges after 30 hours use or monthly. Can be cleaned in a dishwasher. Use mild detergent, rinse, and dry thoroughly.
Replace optional carbon filter after 120 hours use. Remove old filter by turning, insert new one, and re-secure filter cartridges.
Clean hood exterior with soapy water. Avoid abrasive cleaners or sponges. Wipe down with a soft, damp cloth for best results.
Turn off power before changing. Remove lighting port, replace halogen bulb, and re-install port. Follow reverse steps for reassembly.
Guide on maintenance for surfaces, filter cartridges, and carbon filters. Details tasks, frequency, and recommended products for upkeep.
Instructions available online. Heed advice for safety and protection of others during installation and use.
Appliance for home use only. Not for commercial/industrial use. Children under 8 and persons with reduced capacities require supervision.
Disconnect power before touching terminals. Damaged power cord must be replaced by manufacturer or qualified person to avoid danger.
Obey air evacuation regulations. Air must not go into gas/fuel appliance ducts. Ensure room ventilation when using hood with gas appliances.
Do not flambé or turn on uncovered gas rings. Monitor fryers. Clean filters regularly to prevent grease buildup and fire hazards.
Appliance packaging is recyclable. Contact local authorities for disposal points. Thank you for helping protect the environment.
Diagram illustrating the cooker hood's dimensions, including height adjustments and width/depth specifications for installation.
Connect hood to external outlet via flue (min Ø 125mm). If flue is smaller, use recycling mode. Ensure safe distance from cooking hob.
For homes without external outlets. Requires an active carbon filter to absorb odours. See Chapter 4 for filter replacement instructions.
Ensure adequate voltage and good wire condition. Connect to accessible socket. Use 10 or 16A fuse. Consult electrician for installation changes.
Install hood respecting ventilation rules and minimum distance. Mark wall, drill holes, fix support, attach sleeve, and secure hood body.
Instructions for fixing the duct support U-bracket and attaching ventilation ducts and sleeves to the hood and ceiling.
Steps for connecting the hood to an external duct, including securing brackets, ducts, and making electrical connections for optimal airflow.
Details on fitting duct support, sleeve adapter, deflector, and ducts for recycling mode. Includes tips for optimal use and warnings.
Explains the function of each push button (stop, speed settings, light) and provides a diagram of the control panel for user reference.
Clean filter cartridges after 30 hours use or monthly. Can be cleaned in a dishwasher. Use mild detergent, rinse, and dry thoroughly.
Replace optional carbon filter after 120 hours use. Remove old filter by turning, insert new one, and re-secure filter cartridges.
Clean hood exterior with soapy water. Avoid abrasive cleaners or sponges. Wipe down with a soft, damp cloth for best results.
Turn off power before changing. Remove lighting port, replace halogen bulb, and re-install port. Follow reverse steps for reassembly.
Guide on maintenance for surfaces, filter cartridges, and carbon filters. Details tasks, frequency, and recommended products for upkeep.
General| Power requirements | 220-240V, 50Hz |
|---|---|
| Built-in capability | Yes |
| Noise level | 50 dB |
| Intensive speed | No |
| Number of speeds | 3 |
| Type of extraction | Recirculating |
| Maximum extraction power | 600 m³/h |
| Lighting efficiency class | G |
| Fluid dynamic efficiency class | C |
| Motor power | 270 W |
| Energy efficiency scale | A+ to F |
| Type | Wall-mounted |
| Control type | Buttons |
| Product color | Stainless steel |
| Number of filters | 2 pc(s) |
| Grease filter type | Aluminum |
| Bulb type | Incandescent |
| Bulb power | 40 W |
| Number of bulbs | 2 bulb(s) |
| Package weight | 14500 g |
Weight and Dimensions| Depth | 300 mm |
|---|---|
| Width | 600 mm |
| Height | 500 mm |
| Weight | 12000 g |
| Height (max) | 1080 mm |
| Height (min) | 700 mm |
