Braun BP4900 User Manual

8
9
Morning Average (for BP5900 only)
• Press the “Average ” (3) button again into “Morning
Average
” mode, the morning measurements in
memory within past 7 days will show on LCD.
• If there is no data in memory within past 7 days, “
” will
show on LCD.
Evening Average (for BP5900 only)
• Press the “Average ” (3) button once again into “Evening
Average
” mode, the evening measurements in memory
within past 7 days will show on LCD.
• If there is no data in memory within past 7 days, “
” will
show on LCD.
Erasing Data
• Press the “Memory
M
” (2) button into Memory mode.
• Press and hold the “Mode
” (5) button and then press the
“Set
” (4) button, all the stored data will be erased and
CLR will show on screen.
• To check if the data was erased, press the “Memory
M
” (2)
button. No data should show up on screen, but date, time
and M:00.
Morning Hypertension Setting (for BP5900 only)
Morning Hypertension symbol will appear when Morning Average is above your
pre-congured Systolic rate and/or pre-congured Diastolic rate, AND/OR one or both of
these measurements is 20% or more above Evening Average.
** Your pre-congured Systolic / Diastolic should be decided between you and your
doctor or healthcare provider.
• After setting Date and Time, press “Mode
” (5) button
into “Morning Hypertension
” setting mode “- - ” on
Systolic position will ash for Systolic setting.
• Press “SET
” (4) button, LCD will appear 135 mmHg for
SYS as the internal pre-set value, then press “Set
” button
repeatedly to set his own value (Range from 70~250 mmHg)
• Press “Mode
” (5) button again into “Morning
Hypertension
” setting mode “ - - ” on Diastolic position
will ash for Diastolic setting.
• Press “SET
” (4) button, LCD will appear 85 mmHg for DIA
as the internal pre-set value, then user presses “SET
”
button to set his own value (Range for DIA is
40 ~ 115 mmHg).
• User can press START/STOP
(1) button to exit setting
mode and go back to standby at any step.
Irregular Heart Beat Detector (for BP5900 only)
The appearance of this symbol signies that a certain pulse irregularity was detected
during the measurement. Talking, moving, shaking or an irregular pulse during the
measurement can result in the appearance of this icon. Usually this is not a cause for concern,
however if the symbol appears often, we recommend you seek medical advice. The device does
not replace a cardiac examination, but serves to detect pulse irregularities at an early stage.
As a safeguard, we recommend that if you have arrhythmias such as atrial or ventricular
premature beats, artial brillation or any other special conditions, you should check with your
physician before using your blood pressure monitor.
Low Battery Indicator
When the low battery indicator ashes on the display, it means the battery is low and
the four batteries need to be replaced with Alkaline LR6 (AA) batteries.
** After replacing batteries, the Blood Pressure Monitor will go into TIME-SETTING mode automatically
and show the last measurement time on screen. Please SET the current DATE / TIME before taking the
next measurement to get correct AVERAGE result.
Storage and Cleaning
• Always keep the unit in the carrying case after its use.
• Do not put the item directly under the sunlight, in high temperature or humid and dusty places.
• Do not store in extremely low (less than -4°F (-20°C)) or high (more than 140°F (60°C))
temperature.
• Use a piece of cloth with water or mild cleansing agent to clean the case and then use a piece
of dry cloth to wipe it dry. Use a piece of dry cloth to wipe the cu when it is dirty.
• Do not use any strong cleansers to clean it.
• When the unit is not to be used for a long time, remove the batteries.
(Batteries may leak or cause harm).
What to do if …
Problem Reason Solution
Heart Rate
Symbol
Appears in the measurement
condition and ashes when
pulse is detected.
• Measurement in progress, remain quiet.
Low Battery
Indicator
Appears when the battery
voltage is excessively low or
the positions of the batteries
are incorrect.
• Replace all four batteries with new ones.
Insert the batteries in the correct
positions. Be aware of +/- positions.
Measuring
Error
Appears when the accurate
blood pressure and pulse
could not be obtained.
• Press “Start/Stop” button again and
remeasure.
• Check if cu is wrapped according to
instructions.
• Check that there are no kinks in tube.
• Check palm if exerting eort.
• Check if talking or moving during
measurement.
• Check if posture is correct.

Braun BP4900 Specifications

General

Brand	Braun
Model	BP4900
Category	Blood Pressure Monitor
Language	English