BREWISTA Smart Scale II - Mode 5: Auto-tare & Auto-timer (Liquid Start); Mode 6: Pour Over Brewing; Tare Functionality; Tare Button Usage

Auto-o Seng
• Auto-o funcon is set to 180 seconds by default.
• Auto-o can be set to 60 seconds, 120 seconds, 180
seconds, or disabled manually.
• To change the Auto-o me seng or disable this funcon:
❶ Turn o the scale.
❷ Press and hold the ON/OFF buon.
❸ While holding the ON/OFF buon, press the
TARE buon 4-5 mes quickly unl “180”
is displayed.
❹ Release both buons.
❺ Press the MODE buon to switch between
“0/60/120/180”.
◦ If “0” is selected, the Auto-o funcon will
be disabled.
❻ Aer choosing the desired me, press the ON/OFF
buon again.
❼ The display will show “PASS” to conrm this seng.
❽ The scale will turn o automacally.
Note:
◦ If “60”, “120”, or “180” is chosen, the scale will
turn o aer the designated number of seconds of
inacvity.
◦ If the Auto-o funcon is disabled, the scale will
not shut o on its own.
Please note: To maintain a longer baery life, please
turn o the scale by pressing the ON/OFF buon aer
each use.
Silicone Pad
Use of the silicone pad is oponal. It is included to provide
addional water resistance. It also prevents slight weight
variaons caused by abrupt temperature changes on the
plaorm.
• Place the silicone pad onto the plaorm with the Brewista
logo oriented to be read le to right.
• Ensure that the pad covers the plaorm completely
without interfering with plaorm travel.
• The silicone pad is dishwasher safe (top rack).
Washing Instrucons
This scale has been treated with a water-resistant nano-
coang. However, washing the scale under running water is
not recommended. Please follow these instrucons to clean
your scale:
❶ Wash the exterior of the scale with a so, damp cloth.
❷ Do not wash scale under running water.
❸ Leave scale to dry on a dish rack with LCD and buons
poinng up.
DO NOT use liquid bleach or other harsh chemicals.
DO NOT use steel wool or abrasive sponges as this can
scratch the surface.
DO NOT submerge the scale.
Avoid pouring water directly into your scale, as water
may become trapped. If this occurs drying me may
exceed 4 hours.
Water drops on the LCD display will not interfere with
your weighing. These drops will dry and disappear.
If the scale displays “UNST” or the readings jump aer
washing, then water is sll inside the scale. Simply shake
out the excess water and let your scale dry longer.
By following these washing instrucons, you will experience
shorter drying mes and your scale will provide you with years
of reliable service.
Mode 6:
(for Pour Over Brewing)
❶ Place brew vessel on the scale plaorm.
◦ Weight reading goes to 0.0g (Auto-tares).
❷ Add coee grounds to the brewing vessel.
❸ Adjust the amount of coee grounds to the desired
weight.
❹ Once plaorm is stable, press the TARE buon.
❺ Start adding water to the coee grounds.
◦ Count-up mer starts.
❻ Remove cup aer brewing.
◦ Weight reading remains on the display for ve
(5) seconds aer removing the cup.
◦ Aer a ve (5) second delay, me returns to
0’00” and weight returns to 0.0g.
Tare Funcon
• Tare funcon is disabled under “AUTO” mode.
• Under Manual modes: press the TARE buon when
needed.
❹ Remove cup aer brewing.
◦ Weight reading remains on the display for ve
(5) seconds aer removing the cup.
◦ Aer a ve (5) second delay, weight returns to
0.0g.
Mode 5:
(Auto-tare and Auto-mer with mer starng when liquid hits
the cup for espresso preparaon.)
❶ Place cup on the scale.
◦ Weight reading goes to 0.0g (Auto-tares).
❷ Push buon on espresso machine to start the shot.
◦ When liquid hits the cup the mer automacally
starts to count up. To pause the mer, press
TIME buon.
❸ Remove cup aer brewing.
◦ Weight reading remains on the display for ve
(5) seconds aer removing the cup.
◦ Aer a ve (5) second delay, me returns to
0’00” and weight returns to 0.0g.
Calibraon
❶ While the scale is o, press and hold ON/OFF buon and
MODE buon at the same me unl LCD shows internal
code, then release the two buons.
❷ Press the MODE buon again.
◦ The LCD will read “0.0g”.
❸ Place a 500g weight onto the center of the plaorm
◦ The LCD will show internal code.
❹ Press MODE buon again.
❺ The LCD will read “PASS”.
❻ Calibraon is complete.
Warning Messages
• “EEEE”: Overload
◦ Quickly remove weight from plaorm to protect
the scale.
• “UNST”:
◦ Scale is not steady during start up. Please turn o
scale, set on a stable surface and restart scale.
◦ Water is inside the scale. Shake out excess water
and let dry.