Need help?Do you have a question about the Brivis ICE DO-SC18Z9 and is the answer not in the manual?
Details the Brivis ICE series and its fixed speed range.
Essential safety practices for operating and installing the unit.
Lists relevant industry codes, standards, and authorities for installation.
Description and handling of the indoor cooling coil unit.
Instructions for installing the starting collars on the indoor unit.
Guidance on correctly installing the condensate drain P-trap.
Identification of major components within the outdoor unit.
Diagram illustrating a typical installation setup.
Criteria for selecting an appropriate location for the indoor unit.
Requirements for condensate drainage and safety tray installation.
Minimum clearances needed for servicing the indoor unit.
Guidelines for designing efficient ductwork and system airflow.
Instructions for mounting the heater thermistor if applicable.
Importance and accessibility of air filters for the system.
Technical drawings showing indoor unit dimensions.
Guidelines for selecting a suitable location for the outdoor unit.
Electrical connection procedures and compliance standards.
Wiring instructions for connecting the thermostat to the system.
Detailed wiring diagram for the outdoor unit.
Wiring circuit for Brivis StarPro heaters with ICE using Networker.
Wiring circuit for Brivis Classic heaters with ICE using Programmable Thermostat.
Required clearances for the outdoor unit installation.
Critical warnings and cautions for refrigerant handling and piping.
Best practices for designing and installing refrigerant piping.
Table detailing recommended pipe sizes for various lengths.
Limitations and requirements for vertical refrigerant pipe runs.
Table showing capacity adjustments based on pipe length.
Step-by-step guide for connecting refrigerant pipes.
Instructions for charging the system with refrigerant.
Procedures for checking and adding lubricant to the compressor.
Comprehensive steps for initial system start-up and commissioning.
Description of how the system operates in different modes and fault conditions.
Performance data and charts for the DO-SC22Z9 model.
Performance data and charts for the DO-SC18Z9 model.
Detailed specifications for ICE outdoor and indoor units.
Information and fields required for the commissioning sheet.
Introduction to the ICE system and general safety precautions for users.
Information on how Brivis handles user personal data.
Explanation of the operating principles of the Brivis ICE system.
Guide to using the Brivis Networker wall control for system operation.
Explanation of symbols displayed on the Networker control.
Instructions for operating the system in fan-only mode.
Understanding and responding to system error messages.
Procedures for securing the Networker control using a PIN.
Steps to reset forgotten PIN numbers on the Networker.
Recommended monthly and yearly maintenance tasks for the unit.
Overview of the Brivis Care Program for unit upkeep.
Information on how to become a member of the Brivis Care Program.
Details for completing the ICE warranty card or online registration.
Comprehensive terms and conditions of the Brivis warranty.
Warranty periods for different product applications and groups.
Conditions the purchaser must meet to benefit from the warranty.
Items and situations not covered by the warranty.
Purchaser's responsibility for costs related to warranty service.
Specific maintenance tasks the owner must perform.
Consumer rights protected by law in relation to the product.
Details the Brivis ICE series and its fixed speed range.
Essential safety practices for operating and installing the unit.
Lists relevant industry codes, standards, and authorities for installation.
Description and handling of the indoor cooling coil unit.
Instructions for installing the starting collars on the indoor unit.
Guidance on correctly installing the condensate drain P-trap.
Identification of major components within the outdoor unit.
Diagram illustrating a typical installation setup.
Criteria for selecting an appropriate location for the indoor unit.
Requirements for condensate drainage and safety tray installation.
Minimum clearances needed for servicing the indoor unit.
Guidelines for designing efficient ductwork and system airflow.
Instructions for mounting the heater thermistor if applicable.
Importance and accessibility of air filters for the system.
Technical drawings showing indoor unit dimensions.
Guidelines for selecting a suitable location for the outdoor unit.
Electrical connection procedures and compliance standards.
Wiring instructions for connecting the thermostat to the system.
Detailed wiring diagram for the outdoor unit.
Wiring circuit for Brivis StarPro heaters with ICE using Networker.
Wiring circuit for Brivis Classic heaters with ICE using Programmable Thermostat.
Required clearances for the outdoor unit installation.
Critical warnings and cautions for refrigerant handling and piping.
Best practices for designing and installing refrigerant piping.
Table detailing recommended pipe sizes for various lengths.
Limitations and requirements for vertical refrigerant pipe runs.
Table showing capacity adjustments based on pipe length.
Step-by-step guide for connecting refrigerant pipes.
Instructions for charging the system with refrigerant.
Procedures for checking and adding lubricant to the compressor.
Comprehensive steps for initial system start-up and commissioning.
Description of how the system operates in different modes and fault conditions.
Performance data and charts for the DO-SC22Z9 model.
Performance data and charts for the DO-SC18Z9 model.
Detailed specifications for ICE outdoor and indoor units.
Information and fields required for the commissioning sheet.
Introduction to the ICE system and general safety precautions for users.
Information on how Brivis handles user personal data.
Explanation of the operating principles of the Brivis ICE system.
Guide to using the Brivis Networker wall control for system operation.
Explanation of symbols displayed on the Networker control.
Instructions for operating the system in fan-only mode.
Understanding and responding to system error messages.
Procedures for securing the Networker control using a PIN.
Steps to reset forgotten PIN numbers on the Networker.
Recommended monthly and yearly maintenance tasks for the unit.
Overview of the Brivis Care Program for unit upkeep.
Information on how to become a member of the Brivis Care Program.
Details for completing the ICE warranty card or online registration.
Comprehensive terms and conditions of the Brivis warranty.
Warranty periods for different product applications and groups.
Conditions the purchaser must meet to benefit from the warranty.
Items and situations not covered by the warranty.
Purchaser's responsibility for costs related to warranty service.
Specific maintenance tasks the owner must perform.
Consumer rights protected by law in relation to the product.
General| Brand | Brivis |
|---|---|
| Model | ICE DO-SC18Z9 |
| Category | Air Conditioner |
| Language | English |
To Next Page
