Why is thread unravelling at the sewing start on my Brother Sewing Machine?
If thread is unravelling at the sewing start on your Brother Sewing Machine, it may be because the rotary hook pulls the upper thread. To solve this, use the programmer to reduce the intermittent presser foot height so that the upper thread is pressed by the intermittent presser foot at the 1st stitch.
How to prevent my Brother BAS-326G PS Sewing Machine needle from breaking?
To prevent your Brother Sewing Machine needle from breaking, check these points: * If the clearance between the needle and rotary hook tip is too great, adjust the needle clearance. * If the needle is bent, replace it. * Needle deflection can cause breakage, so select a needle suitable for the sewing conditions and reduce the sewing speed. * If the needle is too thin, select a needle suitable for the sewing conditions.
Why is the thread tightening incorrectly on my Brother BAS-326G PS?
If the thread is tightening incorrectly on your Brother Sewing Machine, it could be due to: * Upper thread tension being too weak: Adjust the upper thread tension. * Lower thread tension being too weak: Adjust the lower thread tension. * Thread take-up spring tension and height being incorrect: Adjust the tension and height of the thread take-up spring. * Position of arm thread guide R being incorrect: Adjust the position of arm thread guide R. * Intermittent height of intermittent presser foot being too low: Adjust the intermittent height of the intermittent presser foot.
How to fix thread jamming in my Brother Sewing Machine?
If the thread is jamming in your Brother Sewing Machine, consider these potential causes: * The thread take-up spring tension and height are incorrect, so adjust them. * The needle and rotary hook timing is incorrect, so adjust the needle bar lift amount.
What causes the lower thread to break on a Brother BAS-326G PS?
The lower thread on your Brother Sewing Machine may break if: * The lower thread tension is too strong: Adjust the lower thread tension. * There is damage to the needle hole plate or bobbin case: Repair or replace the problem part.
What to do if the thread slips out of the needle on my Brother BAS-326G PS?
If the thread slips out of the needle on your Brother Sewing Machine: * If stitches are being skipped at the sewing start, refer to "Skipped stitches occur". * If the upper thread trailing length is uneven, adjust the sub tension.
Why is the thread trailing length underneath the material too short on my Brother BAS-326G PS?
If the thread trailing length underneath the material is too short on your Brother Sewing Machine, it's because the fixed knife position is too close to the needle hole plate. Move the fixed knife position away from the needle hole plate.
What to do if my Brother BAS-326G PS Sewing Machine does not operate when the power is on and the foot switch is depressed?
If your Brother Sewing Machine does not operate when the power is turned on and the foot switch is depressed: * Check if the machine head switch cord is disconnected. * If the machine head switch is malfunctioning, replace it with a new one.
What to do if thread wiper does not operate correctly on Brother Sewing Machine?
If the thread wiper on your Brother Sewing Machine isn't operating correctly: * If the thread wiper is obstructing the needle, adjust the height of the thread wiper. * If the thread wiper position is incorrect, adjust the stroke of the thread wiper.
What causes the hitch stitch sewing range to be too great on my Brother Sewing Machine?
If the hitch stitch sewing range is too great on your Brother Sewing Machine, consider the following: * Lower thread tension is too weak: Adjust the lower thread tension. * Lower thread is threaded incorrectly: Pass the lower thread through the window of the inner rotary hook. * Sewing speed is too high: Reduce the sewing speed. * Needle is incorrectly installed: Install the needle correctly.
Explains the meanings of safety indications and symbols used in the manual.
Provides general safety guidelines and precautions for machine operation.
Lists components considered safety devices for the machine.
Details the procedure for mounting the control box.
Explains how to securely mount the sewing machine head.
Describes the safe procedure for tilting the machine head.
Details the process of mounting the operation panel.
Outlines the installation of the pneumatic system components.
Describes how to connect various machine cables and harnesses.
Explains the importance and procedure for grounding the machine.
Details how to safely connect the main power supply.
Details the procedure for attaching the safety eye guard.
Describes the correct procedure for lubricating the sewing machine.
Details how to correctly install the sewing machine needle.
Step-by-step guide for threading the upper thread.
Explains how to operate the foot switch for sewing control.
Instructions for winding the lower thread onto the bobbin.
Details the procedure for correctly installing the bobbin case.
Provides reference values and methods for adjusting thread tension.
Guide to recording, setting, and using custom user programs.
How to record and use cycle programs for sequential pattern sewing.
Steps to reinitialize all memory data to restore normal operation.
Step-by-step guide for performing a sewing operation.
Refers to the lubrication section in INSTALLATION.
Lists error codes related to switch operations and their remedies.
Lists error codes for upper shaft motor issues and their solutions.
Lists error codes for feed mechanism problems and their remedies.
Error codes concerning the work clamp and their associated remedies.
Lists error codes related to communication and memory issues.
Steps to diagnose and fix the machine not operating with power and foot switch.
General| Brand | Brother |
|---|---|
| Model | BAS-326G PS |
| Category | Sewing Machine |
| Language | English |
To Next Page
