How to adjust the stitch lengths in the normal and reverse feed direction to be equal on my Brother Sewing Machine?
If the stitch lengths in the normal feed direction and reverse feed direction are not equal, adjust the eccentric pin.
What to do if skipped stitches occur while sewing with my Brother Sewing Machine?
If skipped stitches occur, check the following: * Replace the needle if it's bent or broken. * Ensure the needle is correctly installed and the machine is properly threaded. * Adjust the presser foot pressure if it's too weak. * Use a thicker needle if the current one is too thin. * Adjust the height of the presser foot if it's too high. * Adjust the height of the needle bar if the needle and rotary hook timing is incorrect. * Adjust the tension of the thread tension spring if it's too weak. * Replace the rotary hook if the tip is broken.
How to fix a Brother DB2-DD7100 when the needle breaks?
If the needle breaks, it might be due to pushing or pulling the material too hard during sewing. Make sure the needle is correctly installed. Replace the needle if it's bent, broken, or the needle hole is blocked. Adjust the height of the needle bar if the needle and rotary hook timing is incorrect. Retard the needle timing if it's advanced too far with respect to the feed dog.
How to fix a Brother Sewing Machine when the upper thread is not tight?
If the upper thread is not tight, it could be because the upper thread tension is too weak, or the lower thread tension is too strong; adjust the upper or lower thread tension accordingly. Also, the needle and feed mechanism timing might be incorrect; advance the needle timing.
Why is the lower thread not tight on my Brother Sewing Machine?
If the lower thread is not tight, it might be because the lower thread tension is too weak, or the upper thread tension is too strong. Adjust the lower or upper thread tension accordingly.
What to do if none of the solenoids operate on my Brother Sewing Machine?
If none of the solenoids operate, check the 8 A fuse inside the control box. If it's blown, check the resistances of all the solenoids and replace any with abnormal resistance.
How to fix incorrect thread trimming on my Brother Sewing Machine when both threads are not being trimmed?
If the upper and lower threads are not being trimmed, replace the fixed or movable knife if they are damaged or worn. Adjust the meshing amount between the fixed and movable knives. Measure the resistance between terminals 3-4 of the sewing machine connector with an ohmmeter; if the measured value is not normal, replace the thread trimmer solenoid.
What does it mean if a Brother DB2-DD7100 Sewing Machine fluorescent lamp flickers?
If the fluorescent lamp flickers, it may indicate that the power supply capacity is insufficient. Adjust the FVR inside the control box.
How to troubleshoot a Brother Sewing Machine when the lower thread is tangled at the start?
If the lower thread is tangling at the sewing start, ensure the bobbin spins in the opposite direction to the rotary hook when the lower thread is pulled. Make sure the bobbin winding amount is not more than 80%. Attach the free spinning prevention spring. Replace the bobbin if it is not turning smoothly. Use only bobbins specified by Brother.
What to do if the oil gauge is not visible in the oil sight glass of my Brother DB2-DD7100?
If the oil gauge is not visible in the oil sight glass, fill the oil tank with oil. Check the rotary hook lubrication amount, and adjust the rotary hook lubrication adjusting screw if it is too loose. Replace the oil gauge if it is damaged.
Overview of the DD7100 single needle direct drive straight lock stitcher.
Details technical specifications for machine head and applications.
Highlights key advantages like built-in motor and dry-head lubrication.
Lists available optional components such as lower thread detector.
Explains operational functions controlled by DIP switches.
Illustrates the step-by-step process for setting machine parameters.
Details adjustable parameters, their ranges, and functions.
Guide for configuring memory switches on the operation panel.
Describes functions and settings for memory switches 01-08 and 11-18.
Details memory switches for backtacking, feed control, and presser foot.
Covers memory switches for thread alarm, rotary hook, and synchronizer.
Diagram and explanation of machine's electrical connectors.
Visual illustration of the sewing machine's components.
General| Max Sewing Speed | 5, 000 stitches per minute |
|---|---|
| Stitch Length | 5 mm |
| Lubrication | Automatic |
| Stitch Options | Straight stitch |
| Automatic Needle Threader | No |
| Drop Feed | Yes |
| Free Arm | No |
| Needle | DB x 1 (size 10-18) |
| Speed | Variable |
| Voltage | 220V |
To Next Page
