Brother DCP-L2510D User Manual

v
Confidential
2. IF YOU REPLACE THE LOW-VOLTAGE POWER SUPPLY PCB ASSY ................................. 4-7
2.1 Reset Irregular Power Supply Detection Counter of
the Low-voltage Power Supply PCB (Function code 88) .................................................... 4-7
3. IF YOU REPLACE THE LASER UNIT ........................................................................................ 4-8
3.1 Entering Adjusted Value of Laser Unit ................................................................................ 4-9
4. IF YOU REPLACE THE PANEL UNIT OR PANEL CONTROL PCB ....................................... 4-11
4.1 Adjusting Touch Panel (Function code 61) (Touch panel models only) ........................... 4-11
4.2 Checking LCD Operation (Function code 12) ................................................................... 4-11
5. IF YOU REPLACE THE ADF UNIT, FIRST SIDE CIS UNIT,
SECOND SIDE CIS UNIT OR DOCUMENT SCANNER UNIT ................................................. 4-12
5.1 Acquiring White Level Data (Function code 55) ............................................................... 4-12
5.2 Scanning and Printing Check ........................................................................................... 4-12
CHAPTER 5 SERVICE FUNCTIONS
1. FUNCTION CODE ....................................................................................................................... 5-1
1.1 How to Enter Maintenance Mode ....................................................................................... 5-1
1.1.1 Method of entering maintenance mode for service personnel ............................... 5-1
1.1.2 Method of entering end-user accessible maintenance mode ................................. 5-2
1.2 List of Maintenance Mode Functions .................................................................................. 5-3
1.3 Details of Maintenance Mode Functions ............................................................................. 5-4
1.3.1 Initialize EEPROM parameters (Function code 01, 91) .......................................... 5-4
1.3.2 Transition to shipping state (Function code 03) ..................................................... 5-5
1.3.3 ADF performance test (Function code 08) ............................................................. 5-6
1.3.4 Print quality test pattern (Function code 09) ........................................................... 5-7
1.3.5 Set worker switches (WSW) and
print worker switch setting data (Function code 10, 11) ......................................... 5-8
1.3.6 Check LCD operation (Function code 12) ............................................................ 5-11
1.3.7 Check control panel key operation (Function code 13) ........................................ 5-13
1.3.8 Display software version (Function code 25) ....................................................... 5-15
1.3.9 Check sensor operation (Function code 32) ........................................................ 5-16
1.3.10 Display LAN connection status (Function code 33) .............................................. 5-18
1.3.11 Set PC print functions (Function code 43) ............................................................ 5-19
1.3.12 Change USB No. return value / Adjust left-end print position /
Adjust upper-end print position /
Change ON/OFF setting for lower case compensation /
Change ON/OFF setting for fixation strength improvement
(Function code 45) ............................................................................................... 5-23
1.3.13 Adjust printable range for each speed level (Function code 46) .......................... 5-27
1.3.14 Transfer received fax data / log information (fax models only)
(Function code 53) ............................................................................................... 5-29
1.3.15 Fine-tune scanning position (Function code 54) .................................................. 5-31
1.3.16 Acquire white level data and set CIS scan area (Function code 55) .................... 5-32
1.3.17 Check toner cartridge (Models with cartridge sensor only) (Function code 57) ... 5-33
1.3.18 Adjust touch panel (Function code 61) ................................................................. 5-35
1.3.19 Continuous print test (Function code 67) ............................................................. 5-36

Brother DCP-L2510D Specifications

General

N-up printing	2, 4, 9, 16, 25
Print technology	Laser
Maximum resolution	1200 x 1200 DPI
Economical printing	Yes
Time to first page (black, normal)	8.5 s
Print speed (black, normal quality, A4/US Letter)	30 ppm
Duplex print speed (black, normal quality, A4/US Letter)	7.5 ppm
Copier resize	25 - 400 %
Maximum copy resolution	600 x 600 DPI
Copy speed (black, normal quality, A4)	30 cpm
Scan to	E-mail, File, Image, OCR
Input color depth	30 bit
Output color depth	24 bit
Maximum scan resolution	19200 x 19200 DPI
Faxing	No
Internal memory	64 MB
Sound pressure level (quiet mode)	44 dB
Display	LCD
Product color	Black
Market positioning	Home & office
Display number of lines	2 lines
Display number of characters	16
Paper tray media types	Plain paper
Paper tray media weight	60 - 163 g/m²
Maximum ISO A-series paper size	A4
Auto Document Feeder (ADF) media weight	60 - 230 g/m²
Direct printing	-
Standard interfaces	USB 2.0
USB 2.0 ports quantity	1
Package depth	517 mm
Package width	580 mm
Package height	434 mm
Package weight	13100 g
Power consumption (off)	0.03 W
Power consumption (sleep)	6.2 W
Power consumption (standby)	42 W
Power consumption (PowerSave)	260 W
Power consumption (average operating)	- W
Energy Star Typical Electricity Consumption (TEC)	1.232 kWh/week
Noise level	48 dB
Sustainability certificates	Nordic Swan Ecolabel, Blue Angel, ENERGY STAR
Included cartridge capacity (black)	700 pages
Total input capacity	250 sheets
Total output capacity	120 sheets
Maximum duty cycle	- pages per month
Harmonized System (HS) code	84433100

Weight and Dimensions

Depth	399 mm
Width	410 mm
Height	272 mm