What to do if Brother Sewing Machine does not start after emergency stop?
If your Brother Sewing Machine does not start after an emergency stop, it may be because the emergency stop switch has not been released. To resolve this, turn the emergency stop switch knob to release it.
Why does the lower thread break on my Brother HE-8000 Sewing Machine?
If the lower thread breaks in your Brother Sewing Machine, try the following: * Thread the bobbin correctly to match the sewing. * Install the needle correctly. * Thread the upper thread correctly. * Adjust the timing of the needle and rotary hook. * Adjust the clearance between the needle and rotary hook. * Adjust the height of the needle bar. * Adjust to an appropriate tension.
What to do if cutter position is incorrect in Brother Sewing Machine?
If the cutter position is incorrect on your Brother Sewing Machine, adjust the cutter to the center of the needle plate cutter groove.
How to fix poor thread tightening on Brother Sewing Machine?
To resolve poor thread tightening on your Brother Sewing Machine, adjust the tack tension and adjust the zigzag tension.
What to do if upper shaft cannot be turned manually in Brother HE-8000 Sewing Machine?
If the upper shaft of your Brother Sewing Machine cannot be turned manually, turn the machine pulley backward to set the needle bar to the needle up position and then return to the home position.
What to do if clearance between upper thread scissors and work clamp is incorrect on Brother HE-8000 Sewing Machine?
If the clearance between the upper thread scissors and work clamp is incorrect on your Brother Sewing Machine, install the upper thread scissors correctly.
General| Brand | Brother |
|---|---|
| Model | HE-8000 |
| Category | Sewing Machine |
| Language | English |
Explains the meanings of safety indications and symbols used in the manual.
Details environmental requirements for machine operation, such as temperature and humidity.
Provides precautions for the safe installation of the sewing machine.
Provides safety precautions related to the sewing process.
Outlines safety precautions to be taken during machine cleaning.
Details safety instructions for performing maintenance and inspection.
Lists and explains the warning labels found on the sewing machine.
Identifies and describes the various parts of the sewing machine with labels.
Describes the different subclasses of the sewing machine and their primary uses.
Lists the technical specifications of the sewing machine, including speed and dimensions.
Illustrates and lists the standard sewing patterns available for the machine.
Describes the function and types of special needle plates.
Lists optional leg parts and standing operation pedals.
Describes tape guard assemblies and ruler options.
Shows the auxiliary table and its sub-table assembly.
Shows the replacement parts set for a 70 mm buttonhole length.
Explains the function of the programmer for setting and transferring data.
Details the power table assembly and model codes for positioning.
Provides dimensional diagrams for vertical positioning of machine components.
Provides dimensional diagrams for horizontal positioning of machine components.
Instructions on installing the motor and flange nuts.
Details the process of installing the control box with mounting hardware.
Instructions for installing the power switch and securing the bed base.
Guidance on installing the machine head onto the bed base.
Instructions for securely tapping the head rest into the table hole.
Describes how to install the operation panel to the work table.
Steps for routing cords and installing the oil stopper plate.
Detailed steps for connecting the ground wire to the control box and machine head.
Instructions for connecting the machine head harness to the control box.
Details on connecting various motor harnesses, including feed, presser foot, and zigzag motors.
Instructions for attaching a plug and connecting the power cord to an AC supply.
Steps for connecting the standing pedal harness and relay harness.
Options for installing the transformer (floor, leg, or treadle support plates).
Instructions on placing and tensioning the V-belt for motor and pulleys.
How to adjust the belt retainer and finger protector.
Instructions for installing the belt cover plate with proper clearance.
Steps for installing the treadle and adjusting its pressure, return pressure, and stroke.
Instructions for changing the treadle unit position for horizontal mounting.
Guidance on assembling and installing the spool stand.
Instructions for installing the eye guard and its support for safety.
Safety precautions and general notes on lubricating the machine.
Steps for lubricating the bed base using the oil level indicator.
Instructions for lubricating the arm via the oil inlet.
Guidance on lubricating the rotary hook race and adjusting lubrication amount.
Steps for attaching the rubber cap and securing the belt cover.
Identifies and explains the functions of the control panel buttons and indicators.
Continues the explanation of control panel buttons and indicators.
Procedures for preparing the machine for home position return.
Explains the different steps of treadle operation and their effects on the work clamp.
Details how to operate the two-pedal and three-pedal standing pedal systems.
Step-by-step guide on how to set up programs and parameters.
Lists parameters, their setting ranges, units, and default values.
Continues the parameter table, detailing settings for zigzag and stitch types.
Continues the parameter table, detailing settings for straight bar tack and running stitches.
Continues the parameter table, detailing settings for front tack patterns and lengths.
Continues the parameter table, detailing settings for rear tack patterns and lengths.
Continues the parameter table, detailing settings for rear tack vector shapes and stitches.
Continues the parameter table, detailing settings for backtacks and cutter operation.
Continues the parameter table, detailing settings for underlay patterns and speeds.
Continues the parameter table, detailing settings for underlay start pitch and zigzag underlay.
Continues the parameter table, detailing settings for tension apply/release timing and rear tack width.
Step-by-step guide on how to change program details and settings.
Instructions on checking and setting the knife length parameter.
Example of setting taper tack for front tack and eyelet for rear tack patterns.
Example of copying settings from one program to another.
Explains the different rear tack vector shape programs.
Describes the four types of underlay patterns and their applications.
Details the four patterns of cutter operation and their settings.
Instructions on setting up cycle programs using multiple patterns.
Steps to change the production counter setting via the operation panel.
Instructions for changing the lower thread counter setting.
How to use and store program memos for quick reference.
Guidance on creating and adding custom patterns using the BAS-PC/300.
Lists parameters that can be checked and changed for BAS-PC/300 created patterns.
Procedure for checking sewing patterns using the test feed mode.
Procedure for checking sewing patterns by manually turning the machine pulley.
Instructions on how to properly install the needle, including types.
Detailed steps for correctly threading the upper thread, including tension adjustments.
Instructions for winding the lower thread onto the bobbin, including adjustments.
Steps for inserting the bobbin into the bobbin case and threading it.
How to adjust thread tension for whip stitch and purl stitch patterns.
How to adjust the thread take-up spring tension and height.
Step-by-step instructions for starting and performing a sewing operation.
Procedures to follow when the emergency stop switch is pressed during sewing.
Steps to take when a thread break is detected during sewing.
Procedures for handling thread breakage that occurs near the end of sewing.
How to resume sewing in test feed or manual mode after an interruption.
Explains the lower thread counter function and its reset procedure.
Instructions on cleaning lint and dust from thread passages and around the work clamp.
Steps for draining oil and cleaning the control box air inlet port.
Guidance on cleaning the eye guard and checking the needle.
Instructions for cleaning the length feed plate and needle plate.
Steps to adjust the needle bar height using a gauge.
Procedure for adjusting the timing between the needle and the rotary hook.
How to adjust the clearance between the needle and the hook point.
How to adjust the overlap between the inner rotary hook and its holder.
Steps to adjust the pressure of the work clamp.
How to install and adjust the knife for proper cutting.
Details on adjusting the upper thread scissors for proper trimming.
Procedure for adjusting the timing of the upper thread scissors opening.
How to adjust the timing of the lower thread clamp.
Steps to adjust the bobbin presser for correct operation.
How to adjust the needle to its correct up stop position.
Explains how to change settings using memory switches.
Lists the available memory switches and their functions/settings.
Steps to initialize all programs and settings on the machine.
Steps to initialize a specific program on the machine.
Instructions for accessing and changing panel DIP switch settings.
Details the functions and default settings for panel DIP switches.
Instructions for accessing and changing DIP switches on the control circuit board.
Details the functions and default settings for DIP switches inside the control box.
Lists various needle plates with their part numbers and dimensions.
Lists needle plates and plastic plates for flat cutters.
Lists work clamp assemblies, finger guards, and work clamps.
Lists various cutter parts with their part numbers and dimensions.
Lists error codes, their causes, and recommended remedies.
Continues the error code table, listing more error codes and their remedies.
Provides a troubleshooting guide for common problems like thread breaks and skipped stitches.
Continues the troubleshooting guide for issues like needle breaks and cutter damage.
To Next Page
