BRP Commander 1000 Can-Am 2013 User Manual

INTRODUCTION
INTRODUCTION
This Shop Manual covers the following BRP made
2013 Can-Am side by side vehicles.
MODEL
ENGINE
TYPE
MODEL NUMBER
Commander
800R
810
6CDA, 6CDB, 6CDC, 6TDA,
6DDA, 6DDB, 6
DDC
Commander
1000
1010
6ADA, 6ADB, 6PDA, 6BDA,
6BDB, 6BDD,
6BDE, 6BDF,
6BDG, 6BDH, 6EDA,
6EDB, 6EDC, 6EDD, 6GDA,
6GDB, 6GDC,
6GDD
The information and component/system descrip-
tions contained in this manual are correct at time
of writing. BRP however, maintains a policy of
continuous improvement of its products without
imposing upon itself any obligation to install them
on products previously manufactured.
Duetolat
e changes, there may be some differ-
ences bet
ween the manufactured product and the
descript
ion and/or specifications in this document.
BRP reserves the right at any time to discontinue
or change specifications, designs, features, mod-
els or equipment without incurring obligation.
VEHICLE INFORMATION
VEHICLE IDENTIFICATION
NUMBER (VIN)
tmr20
11-002-001_a
TYPICAL
1. VIN (Vehicle Identification Number) location
The VI
N (Vehicle Identification Number) decal is lo-
cate
d under the glove box on the passenger side.
VIN Decal Description
tmr2011-002-005_a
TYPICAL — VEHICLE IDENTIFICATION NUMBER LABEL
1. VIN (Vehic
le Identification Number)
2. Model number
3. Manufacturing date
ENGINE IDENTIFICATION
NUMBER (EIN)
tmr201
1-002-002_a
TYPICAL - RH SIDE OF ENGINE
1. Engine Identification Number (EIN)
LIFTING AND SUPPORTING THE
VEHICLE
Front
of Vehicle
1. Place vehicle on a flat non slippery ground.
2. Ensure vehicle shift lever is set to PARK.
3. Inst
all an hydraulic jack under front skid plate.
4. Lift front of vehicle and install a jack stand on
each side under frame section in front of the lip
for center skid plate.
X tmr2013-002
www.MilitaryAtv.com

BRP Commander 1000 Can-Am 2013 Specifications

General

Brand	BRP
Model	Commander 1000 Can-Am 2013
Category	Offroad Vehicle
Language	English

Summary

VIN Decal Description

Vehicle Identification Number (VIN)

Explains the VIN decal and its components, including VIN, model number, and manufacturing date.

Engine Identification Number (EIN)

Refers to the Engine Identification Number (EIN).

Vehicle Information

Vehicle Identification Number (VIN) Location

Specifies the VIN decal is located under the glove box on the passenger side.

Lifting and Supporting the Vehicle

Front of Vehicle

Instructions for safely lifting the front of the vehicle.

Rear of Vehicle

Instructions for safely lifting the rear of the vehicle.

Hoisting the Vehicle

Lifting with Hoist and Strap

Instructions on using a hoist and lifting strap to lift the vehicle by its cage.

Transporting the Vehicle

Loading Procedure

Steps for loading the vehicle onto a trailer or truck bed.

Securing the Vehicle

Instructions for using tie-down straps to securely fasten the vehicle for transport.

Engine Emissions Information

Manufacturer's Responsibility

Outlines manufacturer duties regarding engine emissions certification.

Tightening Torque

Torque Specification Procedures

Details the correct procedure for tightening fasteners and applying torque.

Fastener Grade and Torque Table

Provides a table of torque specifications based on fastener size and grade.

Fastener Information

Metric Fasteners

Notes that most vehicle fasteners are metric and should not be replaced with customary types.

Self-Locking Fasteners

Describes common procedures for working with self-locking fasteners, including cleaning.

Loctite Application Procedure

Common procedures for using Loctite products, emphasizing correct strength selection.

Threadlocker Application

Uncovered Holes (Bolts and Nuts)

Instructions for applying threadlocker to bolts and nuts in uncovered holes.

Blind Holes

Instructions for applying threadlocker to fasteners in blind holes.

Stud Installation in Blind Holes

Procedure for applying threadlocker to studs for blind hole installation.

Pre-Assembled Parts

Applying threadlocker to bolts/nuts in pre-assembled components.

Adjustment Screw

Applying threadlocker to adjustment screws for secure settings.

Repair Procedures

Stripped Thread Repair

Instructions for repairing stripped threads using Loctite FORM-A-THREAD.

Small Holes/Fine Threads Repair

Options for repairing small or fine threaded holes.

Permanent Stud Installation

Procedure for light-duty permanent stud installation.

Gasket Application

Gasket Compound Application

Instructions for applying gasket compound to mating surfaces.

Threadlocker Application for Mounting on a Shaft

Applying threadlocker for mounting components on shafts.

Threadlocker Application for Case-In Components

Applying threadlocker to case-in components, particularly metallic gaskets.