To Next PageTo Next Page
Need help?Do you have a question about the Bruno SRE-1550 Electra-Ride II and is the answer not in the manual?
General| Weight Capacity | 350 lbs |
|---|---|
| Seat Depth | 16 inches |
| Footrest Width | 12 inches |
| Rail Type | Aluminum |
| Rail Length | Customizable |
| Power Source | Battery |
| Seat Type | Padded |
| Seat Features | Swivel |
| Control Type | Joystick |
| Safety Features | Seatbelt, Obstruction Sensors |
Lists all required tools for installing the Bruno Stairway Elevator.
Details on determining installation type and locating rail sections.
Instructions for assembling and installing the bumper bracket.
Procedure for measuring and cutting the rail to the correct length.
Guide to determine staircase angle and define stairway dimensions.
Important notes and procedure for cutting the stairway elevator rail.
Instructions for assembling the rail sections together securely.
Guidance on placing and securing foot clamps for the rail.
Steps to mount the carriage onto the upper section of the rail.
Procedure for setting the correct angle of the carriage.
Instructions for installing the seat assembly onto the carriage.
Procedure for adjusting the seat height for optimal user comfort.
Instructions for assembling and connecting the footrest.
Information and testing of the footrest safety switch.
Instructions for operating the seat swivel and arm rotation features.
Procedure for adjusting the seat armrest width and position.
Installation and adjustment of the final limit switch and actuation ramp.
Procedure for performing a trial run to verify elevator operation.
Details on using the residential infrared call/send system and troubleshooting interference.
Instructions for mounting residential call/send transmitters to the wall.
Procedure for re-learning residential IR transmitters to the unit.
Explanation of audio diagnostic notices and modes for residential units.
Steps to convert the unit for right-hand stairway installation.
Installation of key-controlled call/send transmitters for commercial units.
Explanation of audio diagnostic notices and modes for commercial units.
Steps to convert the unit for right-hand stairway installation for commercial units.
Procedure for testing the operation of call/send transmitters.
Instructions for installing the upper bumper bracket onto the rail.
Procedure for applying grease to the gear rack teeth for smooth operation.
Instructions for mounting the battery charger bracket securely.
Diagram and instructions for connecting the battery charger leads.
Procedure for adjusting the stairway elevator's speed using the potentiometer.
Steps to install the call/send antenna on the rear of the carriage.
Alignment and resetting procedures for the overspeed mechanism.
Information on the built-in circuit breaker and its function.
Procedure for replacing the fuse protecting charging and electronics.
Explanation of battery charger LED indicators and charging status.
Procedure for replacing the AC input fuse for the battery charger.
Checklist of annual maintenance tasks for stairway elevators.
Troubleshooting steps for when the unit does not operate.
Troubleshooting steps for slow operation or lack of power.
Troubleshooting incorrect direction of operation (up/down).
Troubleshooting erratic operation with remote call/send.
Troubleshooting erratic operation with armrest control switch.
Explanation for operation restriction based on seat position.
Troubleshooting non-operation with call/send remote.
Troubleshooting failure to shut off at the end of the rail.
Troubleshooting steps for a rough or chattering ride.
Parts list and diagram for the residential IR transmitter hardware kit.
Parts list and diagram for the commercial keyed call/send hardware kit.
Illustrations and identification of various nut types used in the unit.
Illustrations and identification of various bolt types used in the unit.
Illustrations and identification of various screws and washers used in the unit.
Illustrations and identification of PFHMS screws, washers, and lock washers.
Diagram illustrating the electrical connections for residential units.
Diagram illustrating the electrical connections for commercial units.
Exploded view and parts list for the switch housing assembly.
Exploded view and parts list for the keyed switch housing assembly.
Bill of materials for the main Electra-Ride II components.
Exploded view of rail kits (16', 20', 24') and available options.
Detailed parts list for the carriage assembly.
Exploded view of carriage assembly components.
Exploded view and parts list for the carriage base assembly.
Exploded view and detailed parts list for the seat assembly.
Exploded view and detailed parts list for the footrest assembly.
Exploded view and parts list for the extended footrest assembly.
Exploded view and parts list for the overspeed assembly.
Exploded view and parts list for the keylock switch housing assembly.
Exploded view and parts list for the keyed transmitter assembly.
Detailed exploded view and parts list for the overspeed assembly.
Exploded view and parts list for the standard IR transmitter assembly.
Exploded view and parts list for the complete 16-foot rail kit.
Exploded view and parts list for the complete 20-foot rail kit.
Exploded view and parts list for the complete 24-foot rail kit.
Details of the limited warranty for major components and overall unit.
