EasyManuals Logo

Bryant 558D User Manual

Bryant 558D
68 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #3 background imageLoading...
Page #3 background image
Controls Upgrade Kit (036-150 Units) The controls kit in-
cludes high-pressure, loss-of-charge/low-pressure, and freeze
protection cutout switches. The high-pressure and loss-of-
charge/low-pressure switches can be easily added by screwing
the switches onto Schrader-type fittings provided on the refrig-
erant lines.
SUGGESTED USE:
Kit provides additional protection against system high pres-
sure, loss-of-charge/low pressure, and evaporator coil frost
build-up for 036-150 units.
NOTE: These switches are standard on the 180-300 units.
Condenser Coil Grille (036-150 units) The grille protects
the condenser coil from damage and requires no additional
clearance.
SUGGESTED USE:
When unit is located in high traffic areas or could be subject to
damage.
As an alternate location for the field-supplied disconnect
switch.
FIELD-INSTALLED ACCESSORY
DESCRIPTION AND USAGE
Roof Curbs (Vertical and Horizontal) Full-perimeter galva-
nized steel support frame in 14- and 24-in. high designs pro-
vides wood nailer to attach roof counter flashing. Insulated
basepans in curb are provided to prevent condensation. Duct-
work attaches to rails provided in the roof curb. A gasket is pro-
vided to form an air- and watertight seal between unit and curb.
The gasket meets the standards of the NRCA (National Roofing
Contractors’ Association).
SUGGESTED USE:
Rooftop application for vertical discharge.
Slab-mounted applications when elevation of the unit is
necessary.
Horizontal Adapter (180-300 Units) The curb is prefabri-
cated, easily field-assembled, and permits full perimeter mount-
ing. The curb also improves unit static performance by up to
0.6 in. wg.
SUGGESTED USE:
Rooftop application for horizontal discharge on 180-300 units.
Rooftop applications for horizontal discharge on 180-300
units where high air delivery cfms are required.
Condenser Coil Hail Guard (036-150 Units) Package con-
sists of a hood and coil grille which attach to the condenser coil.
SUGGESTED USE:
To protect the condenser coil from hail and other debris on
036-150 units.
As an alternate location for field-installed disconnect switch.
Condenser Coil Grille (036-150 Units) The grille protects
the condenser coil from damage and requires no additional
clearance.
SUGGESTED USE:
When unit is located in high traffic areas or could be subject to
damage.
As an alternate location for the field-supplied disconnect
switch.
25% and 50% Manual Outdoor-Air Dampers (036-150 Units)
Package consists of a damper which can be set at either
25% or 50% outdoor air (as appropriate). The package includes
a rainhood, birdscreen, and a panel with a hole in it for easy
installation.
SUGGESTED USE:
To allow a fixed percentage of outdoor air for ventilation under
all conditions.
The damper may be used on either vertical or horizontal
applications.
Two-Position Dampers Package consists of a low-leak
damper assembly and a panel with a hole in it for easy instal-
lation (036-150 units). The damper will allow either 0 or 25% or
100% (depending on accessory package) outdoor air into the
unit any time the evaporator fan is running, and features close-
on-power-loss. When the evaporator fan is off, the damper will
be closed.
SUGGESTED USE:
Allows a fixed percentage of outdoor air any time the evapo-
rator fan is on, but closes when the evaporator fan is off to
prevent cold backdrafts and wasted energy.
The damper may be used on either vertical or horizontal air-
flow applications.
Economizers See descriptions listed under Factory-
Installed Options Description and Usage section on page 2.
NOTE: When the accessory Durablade economizer is ordered
for the 036-150 units, the package also contains an outdoor-air
panel for easy installation.
Solid-State Enthalpy Control (036-150 Units) Package
consists of a solid-state control and sensor which is capable of
sensing outdoor-air heat content (temperature and humidity)
and controlling economizer cut-in point to have minimum heat
content air passing over the evaporator coil. The solid-state en-
thalpy control replaces the standard dry-bulb thermostat in the
economizer.
SUGGESTED USE:
To enhance economizer operation for additional energy
savings.
Enthalpy Control Sensor Package consists of a solid-state
sensor to be used in conjunction with the solid-state enthalpy
control (036-150 units) or paired with a second enthalpy sensor
(180-300 units) for differential enthalpy control. This sensor is
mounted on the economizer assembly so that it can sense
building temperature. The 2 sensors will determine which com-
bination of outdoor and return air will provide the greatest en-
ergy savings.
SUGGESTED USE:
To enhance economizer operation for maximum energy
savings.
NOTE: On 180-300 units, a single sensor may be used for
single-sensor, outdoor-air enthalpy control if desired.
Time GuardT II Device Package consists of a control to be
field wired into the unit controls, and provides a 5-minute delay
in compressor operation between cooling cycles.
SUGGESTED USE:
Prevents compressor short cycling when rapid compressor
cycles may be a problem.
Controls Upgrade Kit (036-150 Units) See description
listed under Factory-Installed Options Description and Usage
section on page 2.
Fan/Filter Status (036-150 Units) Provides status of indoor
(evaporator) fan (ON/OFF) or filter (CLEAN/DIRTY). Status
shall be displayed with a field-supplied indicator light at the
thermostat.
SUGGESTED USE:
To assist in servicing the unit.
3

Other manuals for Bryant 558D

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Bryant 558D and is the answer not in the manual?

Bryant 558D Specifications

General IconGeneral
BrandBryant
Model558D
CategoryAir Conditioner
LanguageEnglish

Related product manuals