BUSCH Mink MI 1502 - User Manual

Questions and Answers

Y
ybakerAug 13, 2025
Why does my BUSCH Air Compressor not reach the usual pressure?
- L
  Lindsay CoxAug 13, 2025
  Your BUSCH Air Compressor might not be reaching its usual pressure due to several reasons. It could be a leak in the pressure system, a misadjusted or defective pressure relief valve, or a clogged screen in the gas inlet. There might be clogging in the suction, discharge, or pressure line, or the lines may be too small in diameter. The inlet non-return valve could be stuck, or internal parts may be worn or damaged. To troubleshoot, check for leaks, adjust or replace the valve, clean the screen, remove any clogging, use a larger diameter line, or have the compressor repaired if internal parts are damaged.
C
cameronronaldAug 16, 2025
What to do if my BUSCH Mink MI 1502 Air Compressor does not start?
- A
  Andrea EdwardsAug 16, 2025
  If your BUSCH Air Compressor isn't starting, it could be due to a few things. First, ensure the drive motor is getting the correct voltage. Also, check if the drive motor starter overload protection is set too low or if a fuse has blown. Lastly, the connection cable might be too small or long, causing a voltage drop. Correct the voltage supply, adjust the trip level, check the fuses, and use a sufficiently dimensioned cable to resolve these issues.
C
Christine AllenAug 21, 2025
Why is my BUSCH Mink MI 1502 Air Compressor running very hot?
- B
  bhortonAug 21, 2025
  If your BUSCH Air Compressor is running very hot, it could be due to insufficient air ventilation, high ambient temperature, or high inlet gas temperature. It may also be caused by insufficient gas transfer or a mains frequency/voltage outside the tolerance range. Ensure the compressor's cooling isn't blocked by dirt, observe permitted temperatures, provide a pressure relief valve, and ensure a stable power supply.
L
loweraymondAug 25, 2025
Why is my BUSCH Mink MI 1502 blocked?
- B
  Barbara ByrdAug 25, 2025
  Your BUSCH Air Compressor could be blocked because solid foreign matter has entered it, there's corrosion from remaining condensate, or it was run in the wrong direction. Make sure the suction line has a screen and filter if needed. Repair the compressor and when connecting it, ensure it runs in the correct direction.
J
Jeremy Lee IIAug 28, 2025
Why is my BUSCH Mink MI 1502 running very noisily?
- R
  Rebecca PowellAug 28, 2025
  If your BUSCH Air Compressor is running very noisily, it could be due to defective bearings, a worn coupling element, low oil level in the synchronising gear, or a damaged synchronising gear. If the coupling element is worn replace it. If the synchronising gear is leaky or damaged, repair the compressor.
B
Bonnie SmithSep 1, 2025
What to do if the BUSCH Air Compressor or the drive motor is blocked?
- A
  Ann WolfSep 1, 2025
  Make sure the drive motor is disconnected from the power supply. Remove the fan cover. Try to turn the drive motor with the compressor by hand. If the unit is still frozen: remove the drive motor and check the drive motor and the compressor separately. If the compressor is blocked: Repair the compressor.
S
sellerschristopherSep 5, 2025
What to do if the drive motor is defective in my BUSCH Air Compressor?
- J
  Jessica JenningsSep 5, 2025
  Replace the drive motor.
J
Jason WhiteSep 8, 2025
What to do if the drive motor is running, but the BUSCH Air Compressor stands still?
- M
  Melissa BoothSep 8, 2025
  If the drive motor is running but the BUSCH Air Compressor remains still, the coupling between them may be defective. Replace the coupling element.