BUSCH Mink MM 1202 AP User Manual (English)

Other manuals for BUSCH Mink MM 1202 AP

Questions and Answers:

B
Brianna RussoAug 17, 2025
What to do if my BUSCH Air Compressor does not reach the usual pressure?
- H
  Heather HuynhAug 17, 2025
  If your BUSCH Air Compressor isn't reaching its usual pressure, there are several potential causes. First, check all hose and pipe connections for leaks. If the pressure relief valve or regulating system is misadjusted or defective, you may need to adjust, repair, or replace it. Also, inspect the gas inlet screen and filter for clogs, cleaning or replacing them as needed. Partial clogs in the suction, discharge, or pressure lines should be removed, and lines that are too long or have too small a diameter should be replaced with larger ones. Finally, check if the inlet non-return valve is stuck and clean it, or if internal parts are worn or damaged, consider compressor repair by Busch service.
B
Benjamin CooperAug 20, 2025
Why my BUSCH Mink MM 1202 AP does not start?
- E
  Eric DavisAug 20, 2025
  If your BUSCH Air Compressor isn't starting, it could be due to several reasons. First, ensure the drive motor is receiving the correct voltage. Check if the drive motor starter overload protection is set too low, and compare its trip level with the nameplate data, correcting if necessary. Also, examine the fuses to see if any have blown. Finally, make sure the connection cable is adequately sized and not too long, as this can cause a voltage drop.
T
Tanya GrayAug 22, 2025
What to do if my BUSCH Mink MM 1202 AP Air Compressor starts, but labours or runs noisily or rattles?
- K
  Katie WardAug 22, 2025
  If your BUSCH Air Compressor starts but runs with laboring noises or rattles, you should first check the wiring connections against the connection diagram, especially on motors with six coils, and tighten or replace any loose connections. If the compressor is running in the wrong direction, you should do verification and rectification. If there are foreign objects in the compressor or stuck bearings, consider compressor repair by Busch service.
K
Kevin WalkerAug 25, 2025
How to fix a BUSCH Mink MM 1202 AP Air Compressor that is running very hot?
- N
  Nathan MarquezAug 26, 2025
  If your BUSCH Air Compressor is running very hot, first ensure that the cooling is not blocked by dust or dirt. Clean the fan cowlings, fan wheels, ventilation grilles, and cooling fins. If the compressor is in a narrow space, make sure there is enough ventilation. Also, check that the ambient temperature is within the permitted range.
J
Joanna ChaseAug 27, 2025
What to do if the temperature of the inlet gas is too high in my BUSCH Air Compressor?
- O
  otranAug 27, 2025
  If the inlet gas temperature is too high in your BUSCH Air Compressor, be sure to observe the permitted temperatures for the inlet gas. If there is insufficient gas transfer, provide a pressure relief valve. If the mains frequency or voltage is outside the tolerance range, provide a more stable power supply. If a pressure relief valve/regulating system is installed and is misadjusted or defective, adjust, repair, or replace it. Remove any partial clogging of filters, screens, or lines, and use a larger diameter for long suction, discharge, or pressure lines.
D
David SimpsonAug 30, 2025
What to do if my BUSCH Mink MM 1202 AP Air Compressor or the drive motor is blocked?
- D
  Dana HughesAug 30, 2025
  Make sure the drive motor is disconnected from the power supply. Remove the fan cover and try to turn the drive motor with the compressor by hand. If the unit is still frozen, remove the drive motor and check the drive motor and the compressor separately. If the compressor is blocked: Repair the compressor (Busch service). If the drive motor is defective, replace the drive motor (Busch service).
R
rodriguezrobertSep 1, 2025
Why is the drive motor running, but the BUSCH Mink MM 1202 AP Air Compressor stands still?
- S
  Samuel MendozaSep 2, 2025
  If the drive motor is running but the BUSCH Air Compressor remains still, it's likely that the coupling between the drive motor and the compressor is defective. Replace the coupling element, but note that the replacement should be done by Busch service.
D
David AguilarSep 4, 2025
Why my BUSCH Mink MM 1202 AP Air Compressor runs very noisily?
- S
  Stephen OrozcoSep 4, 2025
  If your BUSCH Air Compressor is running very noisily, it could be due to defective bearings, in which case you should repair the compressor (Busch service). Another cause may be a worn coupling element, which you should replace. Low oil level or damage to the synchronizing gear can also cause noise, requiring repair by Busch service.
L
Laura MillerSep 6, 2025
How to troubleshoot a BUSCH Air Compressor that won't start?
- T
  Todd WallaceSep 6, 2025
  If your BUSCH Air Compressor doesn't start, it could be due to a few reasons. First, check the power supply to ensure the motor is getting power. If the power supply is fine, the motor itself might be defective and need replacement. Another potential cause is a defective coupling, which would also require replacement.
S
samantha88Sep 9, 2025
Why is my BUSCH Air Compressor so noisy?
- R
  Ricky DurhamSep 9, 2025
  If your BUSCH Air Compressor is running very noisily, it could be due to a worn coupling, which requires replacement. Another cause could be that the oil level is too low, so topping up the oil may solve the problem. Finally, defective bearings may be the reason and the machine should be repaired (contact Busch).