Bushman Tank User Manual

Bushman Tank
Installaon Guide
Congratulaons on your selecon of a Bushman Tank.
Bushman is known around the world for its quality products. Your
purchase of a Bushman tank demonstrates your commitment to water
conservaon.
Bushman has designed and manufactured your tank to give you long,
trouble-free service. In the unlikely event that a manufacturing fault
emerges, it will be xed or replaced at no cost to you. Please see our
limited warranty document for details.
The important informaon included in this Installaon Guide will help
you prepare for the arrival and installaon of your Bushman tank.
Remember, your tank must be installed correctly to ensure long life
and so as to not void your warranty.
Be aware that the tank is a conned space. DO NOT EVER ATTEMPT TO
ENTER THE TANK.
If you have any concerns or quesons, please call us at:
1-866-920-TANK (1-866-920-8265)
Monday through Friday, 8:00am - 5:00pm CST
99800106 1 of 2 Rev. D 2/19/19
SECURING YOUR TANK
When your tank arrives, please put at least 1” of water into the tank or otherwise secure it from being blown
away by unexpected winds. Bushman takes no responsibility for tanks being damaged in this manner.
ABOVE GROUND TANK POSITIONING ON A PAD
1. Prepare a level area at least one foot larger than the diameter of your tank. Installaon on a level surface is
crical. Install 3-4” of crushed drainage rock (3/4” stones) and tamp to make level. Alternavely, a concrete
pad or pavers can be used.
2. Locate your water tank near an exisng downspout or water source. If installing your tank with a BCK-0001
rst ush accessory kit (recommended) keep the tank within 6’ of the water source. The BCK-0001 has
precut lengths of pipe that are 6’ long.
3. The tank is moved into posion. If posioning requires a crane or other equipment, this cost is at the
purchaser’s expense.
4. The tank must be ed down to prevent it from being blown away. Adding an inch or two of water in the
tank will help keep it secure.

Bushman Tank Specifications

General

Brand	Bushman
Model	Tank
Category	Water Heater
Language	English

Summary

Securing Your Tank

Above Ground Tank Positioning on a Pad

Prepare Pad Surface

Prepare a level area at least one foot larger than tank diameter with 3-4" crushed drainage rock or a concrete pad.

Locate Water Source

Position tank near downspout or water source, within 6' if using BCK-0001 first flush kit.

Move Tank into Position

Move the tank into its final location; crane use costs are at the purchaser's expense.

Secure Tank Against Wind

Tie down the tank to prevent it from being blown away; adding water helps secure it.

Above Ground Tank Positioning on a Structure

Prepare Structure Decking

Prepare a structure with hardwood decking, gaps no greater than 1 inch, supported by strong bearers.

Locate Water Source

Position tank near downspout or water source, within 6' if using BCK-0001 first flush kit.

Lift Tank into Place

Lift the tank using crane or similar equipment; equipment hire costs are at purchaser's expense.

Secure Tank to Stand

Tie down the tank to the stand to prevent it from being blown away; adding water helps secure it.

Winterizing Your Tank

Installation Steps

Connect Downspout to Tank

Install 3" SDR35 PVC from gutter/downspout into the pre-cut hole in the strainer lid, keeping pipe end above basket.

Install Overflow Extension

Install the overflow extension screen onto the tank overflow fitting by pressing it on.

Connect Overflow Pipe

Glue a 90 deg. elbow fitting to the overflow extension and attach a pipe to convey overflow water away.

Install Drain Valve

Install a drain valve (ball valve or spigot) with an adapter fitting to release water from the tank.

Maintenance

Strainer Basket Cleaning

Remove the 3 screws holding the lid and strainer, clean debris from the basket, and re-install.

Overflow Extension Cleaning

Pull off the press fit screened overflow extension fitting, clean debris, and re-install.