Why is the charging indicator on my BW Technologies Security Sensors still showing after 6 hours?
If the charging indicator on the LCD shows the battery is still charging after 6 hours, it likely means the battery is trickle charging. This indicates that the battery is fully charged and ready for operation.
Why does the battery indicator not display when charging my BW Technologies Security Sensors?
If the battery indicator does not display when charging, it could be because the battery is depleted below normal levels. Charge the battery for 8 hours.
Why are features and options not operating as expected on my BW Technologies Security Sensors?
If features and options are not operating as expected, verify that the settings in Fleet Manager II are correct.
General| Brand | BW Technologies |
|---|---|
| Model | GasAlertMax XT II |
| Category | Security Sensors |
| Language | English |
Lists the detector components and references figures/tables.
Describes the elements shown on the detector's LCD screen.
Explains the function of the detector's pushbutton.
Describes the battery test performed by the detector during startup.
Explains the audible and visual self-test performed at startup.
Displays the current firmware version installed on the detector.
How startup messages are displayed on the detector's LCD.
Details the location logging feature and how to enter site IDs.
Information on how alarm setpoints are displayed during startup.
Screens displayed when the pump test fails.
Displays factory setpoints for TWA and STEL alarms.
Screens displayed when the self-test fails with lockout enabled.
Error message display when self-test fails with lockout disabled.
How the detector performs auto zero during startup.
Screens indicating a previous failed calibration.
Describes the force calibration option when a sensor is past due.
Screens displayed after an unsuccessful bump test.
Recommends daily bump tests to ensure sensor response.
Indicates when all startup tests are passed.
How to use Fleet Manager II to configure detector settings.
Configuration for the top line of the startup message.
Configuration for the bottom line of the startup message.
Enables/disables detector lockout on self-test errors.
Configuration for Safe Mode, Confidence Beep, and Latching Alarms.
Manages calibration requirements for overdue sensors.
Ensures sensors respond correctly to test gas via bump tests.
Restricts calibration to IR Link or MicroDock II.
Logs the location where the detector is used.
Verifies pump operation by comparing flow against blocked flow.
Sets the interval for recording datalog samples.
Defines how often the confidence beep occurs.
Selects the display language for the detector.
Adjusts settings for individual sensors.
Safely disables a sensor if it's not needed or faulty.
Sets the gas concentration value for calibration.
Defines how often each sensor requires calibration.
Sets the low alarm setpoints for sensors.
Sets the high alarm setpoints for sensors.
Sets Time-Weighted Average alarm parameters.
Sets Short-Term Exposure Limit alarm parameters.
Defines the time period for STEL alarms.
Defines the duration for TWA moving average calculation.
Compensates LEL readings for hydrocarbons other than methane.
Configures 50% LEL, LEL by Volume CH4, and 10% Over-span.
Enables Auto Zero on Startup and sets 20.8 Base Reading.
Allows temporary disabling of audible low alarm.
Describes the multi-gas alarm condition and display.
Describes the over limit alarm condition and display.
Describes the low battery alarm condition and display.
Detects low battery and deactivates the detector.
Describes the process of normal detector deactivation.
Alerts user if pump stops or becomes blocked.
Covers Confidence Beep and Heartbeat status indicators.
How to view and clear TWA, STEL, and MAX readings.
How to stop gas alarms and reset them.
Detects missing or defective sensors during startup.
Alerts user if pump stops or becomes blocked.
Alerts user when the battery voltage is low.
Procedures for performing an automated bump test.
How the detector tests ambient air and test gas for calibration.
Procedures for connecting the gas cylinder for calibration.
Automatically zeroes sensors before calibration.
Screens displayed if the sensor fails the span calibration.
Records datalog samples for creating reports.
How to download log files to a PC.
Specifies the maximum hose length for sampling.
Guidelines for maintaining the detector's battery.
Instructions on how to replace the detector's battery.
Procedures for replacing sensors or sensor filters.
To Next Page
