Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect
yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage!
Retain instructions for future reference.
REMINDER: Keep your dated proof of purchase for warranty purposes!
Attach it to this manual or file it for safekeeping.
READ AND FOLLOW ALL INSTRUCTIONS • SAVE THESE INSTRUCTIONS • DO NOT DISCARD
© 2014 Campbell Hausfeld/Scott Fetzer
For parts, product & service information
visit www.campbellhausfeld.com
REGISTER YOUR PRODUCT ONLINE NOW! http://www.campbellhausfeld.com
See Warranty on page 4 for important information about commercial use of this product.
Operating Instructions and Parts Manual HV2000 and HV3000 Series
HVLP Turbine
IN206601AV 9/14
Description
Campbell Hausfeld HVLP turbines are
designed to generate a High Volume
of Low Pressure air for operating HVLP
spray guns. These turbines operate
differently than air compressors because
turbines do not require an air tank to
hold compressed air. Since there is no
compression of air, HVLP turbines do
not create condensation in the air hoses
as compressors often do. Consequently,
the project is not at risk of condensation
contaminating the coating material. The
air generated by the turbine is generally
warm due to the air working in the
turbine. The warm air can be a benefit
for accelerating drying in less than ideal
weather conditions and for drying the
spray gun components. HVLP turbines
are portable, can be plugged into
standard outlets and operate and sound
similar to shop-vacs.
Unpacking
When unpacking the unit, inspect
carefully for any damage that may have
occurred during transit. Make sure any
loose fittings, bolts, etc., are tightened
before putting sprayer into service. Each
unit has been tested before shipment.
Do not readjust or modify the turbine
components.
Attention: Campbell Hausfeld recommends that servicing other than that shown in the instruction manual should be performed
by an authorized service facility. NOT INTENDED FOR CONTINUOUS USE.
Record the serial number and date of
purchase in the space below.
Serial Number _____________________
Date of purchase ___________________
Retain these numbers for future
reference.
Specifications
MODEL HV2000
CFM .........54 CFM at turbine outlet
Operating Pressure ..........4 PSI Max.
Motor Type ........Brush type, 2 stage,
Tangential
Hose Length ........15 ft. (30 ft. Max.)
Transfer Efficiency...........86% Max.
Weight ................... 15 Pounds
Voltage ..............120V, 10.1 Amp
Stub Hose........................No
Storage Compartment ............ Yes
MODEL HV2500
CFM .........58 CFM at turbine outlet
Operating Pressure ..........5 PSI Max.
Motor Type ........Brush type, 2 stage,
Tangential
Hose Length ........25 ft. (40 ft. Max.)
Transfer Efficiency...........86% Max.
Weight ................... 26 Pounds
Voltage ............... 120V, 11 Amp
Stub Hose....................... Yes
Storage Compartment ............ Yes
MODEL HV3000
CFM .........65 CFM at turbine outlet
Operating Pressure ..........6 PSI Max.
Motor Type ........Brush type, 3 stage,
Tangential
Hose Length ........25 ft. (50 ft. Max.)
Transfer Efficiency...........86% Max.
Weight ................... 28 Pounds
Voltage ..............120V, 13.8 Amp
Stub Hose....................... Yes
Storage Compartment ............ Yes
COMPONENTS
(1) Turbine
(1) Hose and quick connect fitting
assemble and clean the unit (storage
compartment)
(1) Wrench - the only tool needed to
assemble and clean the unit (storage
compartment)
(1) Viscosity stick (storage compartment)
(1) Cleaning brush (storage
compartment)
To Next Page
General
