Canature CAN165HIM-100

Questions and Answers

Z
zthompsonAug 14, 2025
Why is the water from my Canature CAN165HIM-100 Water Dispenser hard?
- A
  Ashley HornAug 14, 2025
  If the water from your Canature Water Dispenser is hard, several factors could be responsible: * The by-pass valve might be open; in that case, close the by-pass valve. * The unit might be out of salt; add salt to the tank. * The injector or screen could be plugged; clean these parts. * There might be a blocked water flow to the brine tank; check the brine tank refill rate. * Hard water might be present in the hot water tank, which requires repeated flushing. * A leak could exist between the valve and the central tube; inspect the central tube for cracks or o-ring damage and replace any faulty parts. * There may be an internal valve leak, requiring replacement of the valve seals, spacer, and piston assembly.
K
Kurt KimAug 17, 2025
How to fix low water pressure in Canature Water Dispenser?
- K
  Kevin ChandlerAug 17, 2025
  If you're experiencing low water pressure with your Canature Water Dispenser, the issue might stem from: * Iron or scale buildup in the line feeding the unit. In this case, you should clean the pipes. * Iron buildup inside the valve or tank. To resolve this, clean the control and add resin cleaner to clean the bed, also increase regeneration frequency. * The inlet of the control being plugged by foreign material. If this is the case, remove the piston and clean the control valve.
Z
Zachary LarsenAug 21, 2025
What to do if Canature CAN165HIM-100 fails to start regeneration cycle?
- C
  Carla JohnsonAug 21, 2025
  If your Canature Water Dispenser fails to start a regeneration cycle, consider these potential causes: * **No power supply:** Check the electrical service and fuse. * **Defective circuit board:** Replace any faulty parts. * **Power failure:** Reset the time of day.
A
alexanderwilliamAug 25, 2025
What causes too much water in brine tank of Canature CAN165HIM-100 Water Dispenser?
- S
  Shannon PetersAug 26, 2025
  If there's too much water in the brine tank of your Canature Water Dispenser, it could be due to: * A plugged injector or screen. Cleaning these parts may resolve the issue. * The valve not regenerating, which may require replacing the circuit board, motor, or control. * Foreign material in the brine valve. Cleaning the parts is recommended.
M
Marissa WalterAug 28, 2025
How to stop continuous flow to drain in Canature CAN165HIM-100 Water Dispenser?
- T
  tjohnsonAug 28, 2025
  If water is continuously flowing to the drain in your Canature Water Dispenser, consider these possibilities: * Incorrect valve settings. Ensure that you check and correct the valve settings. * Foreign material in the control valve. Clean the control to remove any obstructions. * An internal leak. If this is the case, replace the seals, spacers, and piston assembly.
C
Christina ChapmanAug 31, 2025
Why Canature Water Dispenser is not drawing brine?
- B
  Brian ThomasAug 31, 2025
  If your Canature Water Dispenser isn't drawing brine, here are a few things to check: * The drain line flow control could be plugged. Clean the parts. * The injector or screen might be plugged. Clean these parts as well. * The inlet pressure may be too low. Increase the pressure to 25 PSI. * There could be an internal valve leak. In this case, replace the seals, spacers, and piston assembly.
B
brad78Sep 3, 2025
Why is there resin in drain line of Canature Water Dispenser?
- F
  felicia90Sep 3, 2025
  If you find resin in the drain line of your Canature Water Dispenser, the causes could be: * Air in the water system. Check the well system for proper air eliminator control. * Incorrect drain line flow control (DLFC) button. Check for the proper flow rate.
C
Christine LambertSep 7, 2025
What causes high salt use in Canature Water Dispenser?
- C
  christophermichaelSep 7, 2025
  If salt use is high in your Canature Water Dispenser, it could be that the refill time is too high. Check the refill time setting.
A
Alexis MontoyaSep 10, 2025
What to do if valve continuously cycles in Canature CAN165HIM-100?
- R
  ramireztimothySep 10, 2025
  If the valve of your Canature Water Dispenser is continuously cycling, it may be due to a defective position sensor PCB. If that's the case, replace the faulty parts.