Candy CAF35PET 011 - Assembling Your Cleaner; Cleaner Maintenance

2
GETTING TO KNOW YOUR CLEANER
A. Dust Container Release Button
B. Variable Power Control Rotary Knob
C. On/O Pedal
D. Parking Slot
E. Exhaust lter cover
F. Dust Container Lid
G. Cord Reel Pedal
H. Dust Container
I. Dust Container Flap
J. Hose
K. Hose Handle
L. Suction Regulator
ASSEMBLING YOUR CLEANER
Remove all components from the packaging.
1. Connect the hose to the cleaner main body, ensuring it clips and locks into position. [1]
2. To release: Simply press two side buttons on the hose end and pull.
3. Connect the hose handle to the upper extension tube end [2], or accessories if required.
4. Connect the extension tube lower end to the carpet and oor nozzle** [3] or accessories
if required.
USING YOUR CLEANER
1. Extract power cord and plug it into the power supply. Do not pull the cord beyond the red
marker. [4]
2. Adjust the telescopic tube to the desired height by moving the telescopic tube adjuster up
and raise or lower the handle to the most comfortable cleaning position. [5]
3. Carpet & Floor Nozzle**. Press the oor type selector on the nozzle [9] to select the ideal
cleaning mode for the oor type.
Hard Floor – Brushes are lowered to protect the oor.
Carpet – Brushes are raised for the deepest clean.
4. Switch the cleaner on by pressing the on/o Pedal on the cleaner main body. [6]
5. Adjust the variable power control rotary knob to increase or decrease the power according
to your cleaning needs. [7]
6. Adjust the suction regulator on the handle to the desired level. [8]
PARKING AND STORAGE SECTION
The tube and nozzle can be parked at the back of the cleaner for storage or temporary storage
while in use. [11]
ACCESSORIES
To obtain the best performance and eciency it is recommended that the correct nozzles
are used for the main cleaning operations. These nozzles are indicated in the diagrams by the
letters GP, HF or CA.
A nozzle type GP can be used to clean both carpet and hard oor.
A nozzle type HF is suitable for use only on hard oor.
A nozzle of type CA is suitable for use only on carpet.
The other nozzles are accessories for specialist cleaning tasks and are recommended for
occasional use only.
All accessories can be tted to the hose handle or to the end of the tubes.
2 in 1 Tool combines several functions into one tool:
Crevice Tool – For corners and hard to reach areas.
Dusting Brush – For bookshelves, frames, keyboards and other delicate areas.
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet hairs
removal.
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for allergen
removal.
Parquet Nozzle* – For parquet oors and other delicate oors.
IMPORTANT: Do not use the Mini Turbo Nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush is rotating.
*Certain Models Only ** Certain models only, nozzles may vary according to model
M. Telescopic Tube Adjuster
N. Telescopic Tube
O. Carpet & Floor nozzle (GP)**
P. Floor type selector pedal
Q. Exhaust Filter
R. Cyclone Body
S. Cyclone Body Cover
T. Pre-motor Filter assembly
U. 2 in 1 accessory
V. Pet Hair Remover Mini Turbo Nozzle*
W. Allergen Remover Mini Turbo Nozzle*
X. Parquet Nozzle*
CLEANER MAINTENANCE
Emptying the Dust Container
When the dust reaches the max level indicator on the container, empty the dust container.
IMPORTANT: To maintain optimum performance, do not allow the dust to exceed the Max level.
1. Turn o the cleaner pressing the on/o Pedal on the cleaner main body and unplug the
power cable.
2. Press the dust container release button and remove the dust container assembly from
the cleaner. [12]
3. Hold the dust container with one hand and open the dust container ap by pulling the
latch. [13]
4. Close the dust container ap and ret to the cleaner main body.
Cleaning the Washable Filters
The cleaner is tted with pre-motor lter and exhaust lter. To maintain optimum cleaning
performance, regularly remove the lters and tap against the side of the dust container to
release dust. The lters should be washed every 5 dust container empties or when the lter has
excessive dust level.
IMPORTANT: All bagless cleaners require regular lter cleaning. Failure to clean your lters
GB