Candy CAF35PET 011 - User Checklist

3
USER CHECKLIST
Should you have a problem with the product, complete this simple user checklist before calling
your local Candy service.
• Is there a working electricity supply to the cleaner? Please check with another electrical
appliance.
• Is the dust container over-lled? Please refer to ‘Cleaner Maintenance’.
• Is the lter blocked? Please refer to ‘Cleaner Maintenance’.
• Is the hose or nozzle blocked? Please refer to removing a blockage from the system.
• Has the cleaner overheated? If so, it will take approximately 30 minutes to automatically reset.
*Certain Models Only ** Certain models only, nozzles may vary according to model
may result in air blockage, overheating and product failure. This may invalidate your guarantee.
IMPORTANT:
Regularly check and maintain the lters.
IMPORTANT: Always ensure the lter pack is fully dry before using.
To access the lter:
1. Remove the dust container from the cleaner. [12]
2. Hold the dust container with one hand and with the other hand open the dust container
lid by pulling the latch. [14]
3. Remove the pre-motor lter assembly from dust container assembly. [15]
4. Gently tap and wash the pre-motor lter assembly. Do not use hot water or detergents.
Remove excess water from the lter assembly and leave to dry fully before re-using. [17,21]
5. Reassemble the pre-motor lter assembly once fully dry and ret to the cleaner.
To access the exhaust lter:
1. Unclip the exhaust lter cover from the rear of the cleaner main body. [18]
2. Remove the exhaust lter from the rear of the cleaner. [19]
3. Gently tap and wash the lter using warm water. Do not use hot water or detergents.
Remove excess water from the lter and leave to dry fully before re-using. [20,21]
4. Ret the exhaust lter to the rear of the cleaner once fully dry and ret the exhaust lter
cover.
IMPORTANT: Do not use the product without the lter pack tted.
Cleaning the dust container / separation unit
This cleaner uses a separation system unique to Candy. If it is necessary to clean the separation
unit, it can be disassembled from the dust container and cleaned.
1. Press the dust container release button and remove the dust container assembly from the
cleaner. [12]
2. Hold the dust container with one hand and with the other hand open the dust container
lid by pulling the latch. [14]
3. Remove the pre-motor lter assembly from the dust container assembly. And then
remove the separation unit from the dust container by pulling. [15]
4. If necessary, use a cloth to remove excessive dust from the separation unit surface.
5. Place the separation system under the Tap as shown. [17] Rinse with lukewarm water.
Wash internal surfaces of the dust container with water only. DO NOT use soap or
detergents to wash the internals of the dust container.
6. Reassemble the internal component to the dust container.
7. Close the dust container lid onto the dust container. Ret the dust container to the
cleaner.
Removing a blockage
1. Check if the dust container is full. If so refer to ‘Emptying the dust container’.
2. If the Dust Container is empty, but suction is still low:
A. Do the lters need cleaning? If so refer to ‘Cleaning the washable lters’.
B. Check if there is any other blockage in the system - Use a rod or pole to remove any
blockage from the extension tube or exible hose.
C. Check if pre-motor lter is tted.
D. Check if the separation unit needs to be cleaned. Refer to ”Cleaning the separation
unit”.
WARNING - If the cleaner is used for a signicant period of time with a blockage, a thermal cut
out will switch the cleaner o to prevent overheating. If this should happen, switch the cleaner o,
unplug and correct the fault. It will take about 45 minutes for the cut out to automatically reset.
IMPORTANT INFORMATION
Candy Spares and Consumables
Always replace parts with genuine Candy spares. These are available from your local Candy
dealer or direct from Candy. When ordering parts always quote your model number.
Quality
Candy’s factories have been independently assessed for quality. Our products are made using a
quality system which meets the requirements of ISO 9001.
Your Guarantee
The guarantee conditions for this appliance are as dened by our representative in the country
in which it is sold. Details regarding these conditions can be obtained from the dealer from
whom the appliance was purchased. The bill of sale or receipt must be produced when making
any claim under the terms of this guarantee.
Subject to change without notice.
GB