Canton musicbox Air 3 User Manual (English)

Other manuals for Canton musicbox Air 3

Questions and Answers:

D
David AndersonSep 5, 2025
What to do if there is no connection between router and Canton Stereo Receiver musicbox Air 3?
- R
  rodriguezcaseySep 6, 2025
  This may be happening because you are not holding the WPS button on your router. First press the WP SETUP button at the musicbox Air 3 until the LED ring is blinking alternating green and blue. Thereafter, press and hold the WPS button on your router for the duration of the registration process. Also, make sure that you press the WPS button on your router within one minute after starting the WP SETUP Mode, because the musicbox Air 3 is in WP SETUP Mode for approximately two minutes.
S
shannon27Aug 25, 2025
What to do if my Canton Stereo Receiver musicbox Air 3 does not respond?
- S
  Sarah Schroeder MDAug 25, 2025
  If your Canton Stereo Receiver musicbox Air 3 is not responding, try turning it off and on again using the POWER button. It may have hung.
N
Nicole AustinAug 25, 2025
How to fix no music playback on Canton Stereo Receiver musicbox Air 3?
- J
  John PageAug 26, 2025
  If you are experiencing no music playback on your Canton Stereo Receiver musicbox Air 3, make sure that the musicbox Air 3 and the playback device are connected to the same network. Also, reduce the distance between the musicbox Air 3 and the playback device or the WLAN router.
K
ksotoAug 27, 2025
What to do if my Canton Stereo Receiver musicbox Air 3 cannot be selected as a network?
- J
  John BurtonAug 27, 2025
  If your Canton Stereo Receiver musicbox Air 3 cannot be selected as a network, consider the following: 1. Wait a moment, as the musicbox Air 3 requires up to 60 seconds to initialize the network and to be displayed in the network router. 2. Check that the WLAN adapter of your WLAN-compatible device (e.g. notebook) is activated. Refer to the instructions provided with the WLAN device if needed. 3. Remove the network cable from your WLAN-compatible device, as only a wireless (WLAN) connection is permitted. 4. Ensure the musicbox Air 3 has been set into the manual connection mode by pressing the WP SETUP button until the LED ring blinks alternating red and blue. If it blinks green and blue, the button was not pressed long enough.
R
Robert RosarioAug 27, 2025
What to do if my Canton Stereo Receiver musicbox Air 3 does not work and all LEDs are off?
- H
  Heather Williams DDSAug 27, 2025
  If your Canton Stereo Receiver musicbox Air 3 does not work any longer, all LEDs are off or the LED ring is blinking blue because the update process was interrupted, leave the musicbox Air 3 connected to the mains for at least 30 minutes. After this time, try performing a firmware update over the network.
R
Ronald ChanSep 13, 2025
How to reset Canton Stereo Receiver musicbox Air 3?
- P
  Paula PettySep 13, 2025
  If the musicbox Air 3 has been hung, reset the musicbox Air 3, if necessary. Press and hold the RESET button on the back until the LED ring is blinking green rapidly (2x per second).
S
Stephanie MontoyaSep 12, 2025
What to do if Canton Stereo Receiver musicbox Air 3 does not respond?
- C
  Cameron HowardSep 12, 2025
  If the musicbox Air 3 has been hung, turn the musicbox Air 3 off and on again using the POWER button.
A
Angelica JohnsonSep 12, 2025
How to update Apple device firmware for Canton Stereo Receiver?
- T
  Tyler RiceSep 12, 2025
  If the operating system (firmware) installed on your Apple device is earlier than iOS Version 4.3.3, update the device firmware. Note: a compatible firmware version is not available for iPod touch (1st and 2nd generation) and iPhone 3G.
M
Mr. Kevin Grimes MDSep 4, 2025
How to fix no music playback on Canton musicbox Air 3 because of Apple device connection?
- D
  dyeramberSep 4, 2025
  If your Apple device is already connected to the musicbox Air 3 over the USB port, disconnect the USB connection between your Apple device and musicbox Air 3 in order to be able to transfer data using AirPlay. An iPod, iPhone or iPad cannot be simultaneously connected via AirPlay and USB.
P
Paige MannSep 2, 2025
Why my Canton Stereo Receiver musicbox Air 3 is not displayed in the router?
- C
  Claudia LewisSep 2, 2025
  This issue may occur because the distance between the network router and musicbox Air 3 is too high. To solve this, reduce the distance between your router and the musicbox Air 3. Another reason might be that you are operating your WLAN router at 5Ghz instead of 2.4 Ghz, so set your router to the operating frequency of 2.4 GHz. In some cases, the musicbox Air 3 had a “system crash”, so reboot the musicbox Air 3 by switching it off and on again using the POWER button. If required, reset the musicbox Air 3 by pressing and holding the RESET button on the back until the LED ring blinks quickly green (2x per second).

Canton musicbox Air 3 Specifications

General

Brand	Canton
Model	musicbox Air 3
Category	Stereo Receiver
Language	English

Canton musicbox Air 3 Operating Instructions

Table of Contents

Other manuals for Canton musicbox Air 3

Questions and Answers:

Canton musicbox Air 3 Specifications