What to do if Canton Stereo Receiver musicbox Air 3 does not work any longer?
If the musicbox Air 3 does not work any longer, and all LEDs are off or the LED ring is blinking blue, the update process was interrupted (e.g. loss of electricity) and the update could not be completed. Leave the musicbox Air 3 connected to the mains for at least 30 minutes. After this time, try performing a firmware update over the network.
What to do if my Canton Stereo Receiver musicbox Air 3 does not respond?
If your Canton Stereo Receiver musicbox Air 3 is not responding, try turning it off and on again using the POWER button. It may have hung.
How to fix no music playback on Canton Stereo Receiver musicbox Air 3?
If you are experiencing no music playback on your Canton Stereo Receiver musicbox Air 3, make sure that the musicbox Air 3 and the playback device are connected to the same network. Also, reduce the distance between the musicbox Air 3 and the playback device or the WLAN router.
What to do if my Canton Stereo Receiver musicbox Air 3 cannot be selected as a network?
If your Canton Stereo Receiver musicbox Air 3 cannot be selected as a network, consider the following: 1. Wait a moment, as the musicbox Air 3 requires up to 60 seconds to initialize the network and to be displayed in the network router. 2. Check that the WLAN adapter of your WLAN-compatible device (e.g. notebook) is activated. Refer to the instructions provided with the WLAN device if needed. 3. Remove the network cable from your WLAN-compatible device, as only a wireless (WLAN) connection is permitted. 4. Ensure the musicbox Air 3 has been set into the manual connection mode by pressing the WP SETUP button until the LED ring blinks alternating red and blue. If it blinks green and blue, the button was not pressed long enough.
What to do if my Canton Stereo Receiver musicbox Air 3 does not work and all LEDs are off?
If your Canton Stereo Receiver musicbox Air 3 does not work any longer, all LEDs are off or the LED ring is blinking blue because the update process was interrupted, leave the musicbox Air 3 connected to the mains for at least 30 minutes. After this time, try performing a firmware update over the network.
How to reset Canton Stereo Receiver musicbox Air 3?
If the musicbox Air 3 has been hung, reset the musicbox Air 3, if necessary. Press and hold the RESET button on the back until the LED ring is blinking green rapidly (2x per second).
What to do if Canton Stereo Receiver musicbox Air 3 does not respond?
If the musicbox Air 3 has been hung, turn the musicbox Air 3 off and on again using the POWER button.
How to update Apple device firmware for Canton Stereo Receiver?
If the operating system (firmware) installed on your Apple device is earlier than iOS Version 4.3.3, update the device firmware. Note: a compatible firmware version is not available for iPod touch (1st and 2nd generation) and iPhone 3G.
How to fix no music playback on Canton musicbox Air 3 because of Apple device connection?
If your Apple device is already connected to the musicbox Air 3 over the USB port, disconnect the USB connection between your Apple device and musicbox Air 3 in order to be able to transfer data using AirPlay. An iPod, iPhone or iPad cannot be simultaneously connected via AirPlay and USB.
Why my Canton Stereo Receiver musicbox Air 3 is not displayed in the router?
This issue may occur because the distance between the network router and musicbox Air 3 is too high. To solve this, reduce the distance between your router and the musicbox Air 3. Another reason might be that you are operating your WLAN router at 5Ghz instead of 2.4 Ghz, so set your router to the operating frequency of 2.4 GHz. In some cases, the musicbox Air 3 had a “system crash”, so reboot the musicbox Air 3 by switching it off and on again using the POWER button. If required, reset the musicbox Air 3 by pressing and holding the RESET button on the back until the LED ring blinks quickly green (2x per second).
Connects the musicbox Air 3 to a WLAN router using the WPS button.
Connects the musicbox Air 3 to a WLAN router via a web interface.
Connects the musicbox Air 3 to an Apple device using a USB cable.
Plays music wirelessly over the network using AirPlay or similar.
Plays music directly from a device without a WLAN router.
Plays music from an Apple device connected via USB.
Plays music from external sources via the analog LINE-IN jack.
Updates the musicbox Air 3 firmware using a USB storage stick.
Updates the musicbox Air 3 firmware via a network connection.
Lists compatible Apple devices and software versions for AirPlay.
Provides legal information regarding trademarks and product compliance.
General| Brand | Canton |
|---|---|
| Model | musicbox Air 3 |
| Category | Stereo Receiver |
| Language | English |
To Next Page
