Instruction manual Di653 17
Please keep this instruction manual for future reference
WATER SOFTENER
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which would have a
detrimental or adverse effect on the operation of the appliance.
The higher the content of these minerals and salts, the harder your water is.
The softener should be adjusted according to the hardness of the water in your area. Your local
Water Authority can advise you on the hardness of the water in your area.
ADJUSTING SALT CONSUMPTION
The dishwasher is designed to allow for adjustment in the amount of salt consumed based
on the hardness of the water used. This is intended to optimise and customise the level of
salt consumption.
Please follow the steps below for adjustment in salt consumption:
1. Open the door and Switch on the appliance.
2. Press the Programme button “
Water Softener
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which
would have a detrimental or adverse effect on the operation of the appliance.
The more minerals there are, the harder your water is.
The softener should be adjusted according to the hardness of the water in your area.
Your local Water Authority can advise you on the hardness of the water in your area.
Adjusting salt consumption
The dishwasher is designed to allow for adjustment in the amount of salt consumed
based on the hardness of the water used. This is intended to optimise and customise
the level of salt consumption.
1. Open the door and switch on the appliance
2. P Program “ ”
3. Program
“ ”
4. Without operation in 5 seconds or press the Power button to complete the setup
and exit the setup mode.
;
ress the button for more than 5 seconds to start the water softener
set model within 60 seconds after the appliance was switched on;
Press the button to select the proper set according to your local
environment, the sets will change in the following sequence:
H3->H4->H5->H6->H1->H2->H3;
Please follow the steps below for adjustment in salt consumption.
dH=1.25 Clarke=1.78 fH=0.178mmol/l
°
°
°
1
The manufactory setting: H3
Contact your local water board for information on the hardness of your water supply.
0 - 5
6 - 11
12 - 17
18 - 22
23 - 34
35 - 55
German
dH
German
dH
Salt consumption
(gram/cycle)
Salt consumption
(gram/cycle)
0 - 9
10 - 20
21 - 30
31 - 40
41 - 60
61 - 98
0 - 6
7 - 14
15 - 21
22 - 28
29 - 42
43 - 69
0 - 0.94
1.0 - 2.0
2.1 - 3.0
3.1 - 4.0
4.1 - 6.0
6.1 - 9.8
H1
H2
H3
H4
H5
H6
0
9
12
20
30
60
French
fH
French
fH
Mmol/lMmol/l
Water softener levelWater softener level
British
Clarke
British
Clarke
WATER HARDNESS
7
“for more than 5 seconds to start the water softener setting
within 60 seconds after the appliance was switched on;
3. Press the Programme button “
Water Softener
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which
would have a detrimental or adverse effect on the operation of the appliance.
The more minerals there are, the harder your water is.
The softener should be adjusted according to the hardness of the water in your area.
Your local Water Authority can advise you on the hardness of the water in your area.
Adjusting salt consumption
The dishwasher is designed to allow for adjustment in the amount of salt consumed
based on the hardness of the water used. This is intended to optimise and customise
the level of salt consumption.
1. Open the door and switch on the appliance
2. P Program “ ”
3. Program
“ ”
4. Without operation in 5 seconds or press the Power button to complete the setup
and exit the setup mode.
;
ress the button for more than 5 seconds to start the water softener
set model within 60 seconds after the appliance was switched on;
Press the button to select the proper set according to your local
environment, the sets will change in the following sequence:
H3->H4->H5->H6->H1->H2->H3;
Please follow the steps below for adjustment in salt consumption.
dH=1.25 Clarke=1.78 fH=0.178mmol/l
°
°
°
1
The manufactory setting: H3
Contact your local water board for information on the hardness of your water supply.
0 - 5
6 - 11
12 - 17
18 - 22
23 - 34
35 - 55
German
dH
German
dH
Salt consumption
(gram/cycle)
Salt consumption
(gram/cycle)
0 - 9
10 - 20
21 - 30
31 - 40
41 - 60
61 - 98
0 - 6
7 - 14
15 - 21
22 - 28
29 - 42
43 - 69
0 - 0.94
1.0 - 2.0
2.1 - 3.0
3.1 - 4.0
4.1 - 6.0
6.1 - 9.8
H1
H2
H3
H4
H5
H6
0
9
12
20
30
60
French
fH
French
fH
Mmol/lMmol/l
Water softener levelWater softener level
British
Clarke
British
Clarke
WATER HARDNESS
7
“ to select the proper setting according to your local
environment, the settings will change in the following sequence:
H3 H4 H5 H6 H1 H2 H3
4. No operation in 5 seconds or pressing the Power button will complete the setup and exit the
setup mode.
WATER HARDNESS
WATER
SOFTENER
LEVEL
SALT CONSUMPTION
(GRAM/CYCLE)
GERMAN °DH FRENCH °FH BRITISH °CLARKE MMOL/L
0~5 0~9 0~6 0~0.94 H1 0
6-11 10-20 7-14 1.0-2.0 H2 9
12-17 21-30 15-21 2.1-3.0 H3 12
18-22 31-40 22-28 3.1-4.0 H4 20
23-34 41-60 29-42 4.1-6.0 H5 30
35-55 61-98 43-69 6.1-9.8 H6 60
°dH=1.25 °Clarke=1 1.78°fH=0.178mmol/l The manufacturer setting: H3
Contact your local water board for information on the hardness of your water supply.
To Next Page
Loading...
