Caple VAP2/3IN1/BS - User Manual

Questions and Answers

K
kjamesAug 14, 2025
Why has the flow reduced in my Caple Plumbing Product?
- D
  Diane BrownAug 14, 2025
  If the flow of your Caple Plumbing Product has reduced, it could be due to low mains water pressure or the Puriti filter needing replacement. Check your water pressure and replace the Puriti filter to resolve the issue.
S
Sandra WallAug 17, 2025
Why is the water not hot in my Caple Plumbing Product?
- M
  Michael WhiteAug 17, 2025
  If your Caple Plumbing Product isn't dispensing hot water, start by checking the power supply to the boiler and ensure it's turned on. Also, verify that the temperature setting isn't set too low and increase it if necessary.
A
Alicia MartinAug 20, 2025
What to do if there is no water flow from my Caple VAP2/3IN1/BS Plumbing Product?
- N
  Nathan NashAug 20, 2025
  If there is no water flow from your Caple Plumbing Product, it might be because the water valve is switched off, or the inlet pipes are twisted. Check these to resolve the issue.
J
jason26Aug 25, 2025
Why is hot water or steam released from the tap when my Caple VAP2/3IN1/BS Plumbing Product is not in use?
- D
  Denise SandersAug 25, 2025
  If hot water or steam are being released from the tap of your Caple Plumbing Product when not in use, the auto-close system on the boiling water handle may have malfunctioned, or the valve is leaking. Replace the spring for the auto-close handle system and replace the valve.
T
Timothy HollandAug 27, 2025
What to do if the water does not flow immediately from my Caple VAP2/3IN1/BS Plumbing Product?
- N
  nolanrussellAug 27, 2025
  If the water does not flow immediately from your Caple Plumbing Product, the boiler tank may not be full of water. Open the tap valve and wait a few minutes until the tank fills. This is normal when first used.
C
Chelsey CherryAug 31, 2025
What does error E2 mean on my Caple VAP2/3IN1/BS and how to fix it?
- D
  david53Aug 31, 2025
  If the E2 error code is displayed on your Caple Plumbing Product boiler screen, it means the tank is heating without water inside. Turn off the power. Fill water into the tank by turning the boiling water lever on the tap. Once full, turn the power back on.
K
Kelly JacksonSep 2, 2025
What does error E1 mean on my Caple VAP2/3IN1/BS?
- R
  Raymond WoodSep 3, 2025
  If you see error code E1 on the boiler screen of your Caple Plumbing Product, it indicates a leakage of electricity. Turn off the power and contact Caple Service.
J
Jenna StricklandSep 6, 2025
What to do if water is icing in the tank of my Caple VAP2/3IN1/BS Plumbing Product?
- M
  maynardnathanSep 6, 2025
  If water is icing in the tank of your Caple Plumbing Product, it indicates an anti-freeze protection failure. If the anti-freeze protection does not solve this issue, turn off the power and contact Caple Service.
T
Tina JonesSep 10, 2025
What does error E3 mean on my Caple VAP2/3IN1/BS?
- M
  Michele AndersonSep 10, 2025
  If the E3 error code is displayed on your Caple Plumbing Product boiler screen, it means a temperature sensor failure. Turn off the power and contact Caple Service.