Carrier 38QRF018 - Page 3

3
(FIELD PROVIDED AND INSTALLED)
NOTE: Dimensions shown in feet-inches. Dimensions in ( ) are millimeters.
UNIT MODELS
CHASSIS
SIZE
(Reference)
ABCDE FG H JKL NP
38QRF
Unit Size
018
0
2 -1
1
/
8
3 -0
15
/
16
1 -2
9
/
16
1 -4 1 -11
7
/
16
1 -5
3
/
16
1 -5
1
/
8
1 -10 1 -1 0 -6
5
/
8
0 -11
1
/
4
0 -2
15
/
16
0 -6
(638.2) (938.2) (369.9) (406.4) (595.3) (436.6) (435) (559.1) (330.2) (168.3) (285.8) (75) (152.4)
024
0.6
2 -7
1
/
8
3 -0
15
/
16
1 -2
9
/
16
1 -4 1 -11
7
/
16
1 -5
3
/
16
1 -11
1
/
8
2 -4 1 -2 0 -6
3
/
4
0 -11
5
/
8
0 -2
15
/
16
0 -6
(790.6) (938.2) (369.9) (406.4) (595.3) (436.6) (587.4) (711.5) (355.6) (171.5) (295.3) (75) (152.4)
030,035,036
1.0
3 -1
3
/
16
3 -8
9
/
16
1 -5
1
/
16
1 -6
7
/
16
2 -6
1
/
2
1 -7
5
/
8
2 -5
3
/
16
2 -10
1
/
16
1 -1
11
/
16
0 -8
1
/
8
1 -3
7
/
8
0 -3
7
/
16
0 -6
1
/
2
(944.6) (1131.9) (433.4) (468.3) (774.7) (498.5) (741) (865.5) (347.7) (206.4) (403.2) (88) (165.4)
UNIT SIZE
M OPERATING WT
in. (mm) lb (kg)
38QRF
HEAT
PUMPS
018
5
/
8
15.88 166 75.3
024
5
/
8
15.88 176 79.8
030
3
/
4
19.05 187 84.8
035
3
/
4
19.05 221 100.2
036
3
/
4
19.05 232 105.2
NOTES: 1. Required clearances: with coil facing wall, allow 6 in. minimum clearance
on coil side and coil end, and 3 feet minimum clearance on compressor end and fan side. With fan facing wall, allow 8 in. minimum clearance on fan side and coil end, and 3 feet minimum clearance on compressor end and coil side. With multi-unit application, arrange units so discharge of one does not enter inlet of another.
2. Dimensions in parenthesis are in millimeters. 3. Center of Gravity .
UNIT SIZE
MINIMUM MOUNTING PAD
DIMENSIONS
Support Feet
ft-in. mm
CHASSIS SIZES 0 & .6 1 -11 x3 -6 584.2 x 1066.8
CHASSIS SIZES 1 & 1.6 2 -0 x4 -2 609.6 x 1270
A07883
Fig. 3 -- 38 QRF Unit Dimensions
38QRF