Carrier 42GCVBE010-703 - Automatic Operation; Cooling; Fan Only Operation; Dry Operation; Hi-Power Operation

Models: 42GCVBE013, 018-703,
42GCVBE013, 018-303P,
42TEVGB013, 018-703
AUTOMATIC OPERATION
5
To automatically select cooling or fan only operation
1. Press
: Select A.
2. Press
: Set the desired temperature.
3. Press
: Select AUTO, LOW , LOW+ , MED ,
MED+
, or HIGH .
1. Press : Select Cool or Fan only .
2. Press
: Set the desired temperature.
Cooling: Min. 17°C, Fan Only: No temperature indication
3. Press
: Select AUTO, LOW , LOW+ , MED ,
MED+
, or HIGH .
DRY OPERATION
COOLING / FAN ONLY OPERATION
7
6
For dehumidification, a moderate cooling performance is controlled
automatically.
1. Press
: Select Dry .
2. Press
: Set the desired temperature.
Hi-POWER OPERATION
8
To automatically control room temperature and airflow for faster cooling
(except in DRY and FAN ONLY mode)
Press
: Start and stop the operation.
ECO OPERATION
9
To automatically control room temperature to save energy (except in DRY
and FAN ONLY mode)
Press
: Start and stop the operation.
Note: Cooling operation; the set temperature will increase automatically 1
degree/hour for 2 hours (maximum 2 degrees increase).
TEMPORARY OPERATION
12
In case of the misplaced or discharged remote control
●
Pressing the RESET button, the unit can start or stop without using the
remote control.
●
Operation mode is set on AUTOMATIC operation, preset temperature
is 24°C and fan operation is automatic speed.
Set the timer when the air conditioner is operating.
Setting the OFF timer
1
Press
for enter OFF timer setting.
2
Press
for select desired OFF timer. (0.5 - 12 hrs)
3
Press
for set OFF timer.
4
Press again for cancel OFF timer.
TIMER OPERATION
10
AUTO RESTART OPERATION
DISPLAY LAMP BRIGHTNESS ADJUSTMENT
13
11
To automatically restart the air conditioner after the power failure (Power of
the unit must be on.)
Setting
1. Press and hold the RESET button on the indoor unit for 3 seconds to
set the operation. (3 beep sound and OPERATION lamp blink 5 time/
sec for 5 seconds)
2. Press and hold the RESET button on the indoor unit for 3 seconds to
cancel the operation. (3 beep sound but OPERATION lamp does not
blink)
• In case of ON timer or OFF timer are set, AUTO RESTART
OPERATION does not activate.
To decrease the display lamp brightness or turn it off.
1. Press and hold
for 3 seconds until brightness level ( , ,
or ) is shown on remote control LCD then release the button.
2. Press
Rise
or
Decrease
to adjust brightness in 4 levels.
Remote control
LCD
Operation display Brightness
Lamp illuminates full brightness.
100%
Lamp illuminates 50% brightness.
50%
Lamp illuminates 50% brightness and the operation
lamp is turned off.
50%
All lamps are turned off.
All turned off
●
In the examples of
and , the lamp illuminates for 5 seconds before
going off.
Note:
● Except 42GCVBE010-703, 42GCVBE010-303P and 42TEVGB010-703.
SELF CLEANING OPERATION
(COOL AND DRY OPERATION ONLY)
14
To protect bad smell caused by the humidity in the indoor unit.
1. If the
button is pressed once during “Cool” or “Dry” mode,
the fan will continue to run for other 30 minutes, then it will turn off
automatically. This will reduce the moisture in the indoor unit.
2. To stop the unit immediately, press the
more 2 times within
30 seconds.
Models: 42GCVBE010-703,
42GCVBE010-303P,
42TEVGB010-703
TH
EN
1110255146_EN.indd 31110255146_EN.indd 3 12/13/2560 BE 14:3212/13/2560 BE 14:32