43
Refer to the Rooftop PremierLink Installation, Start-Up,
and Configuration Instructions (Form 33CS --58SI),
PremierLink Installation, Start --up, and Configuration
Instructions, for detailed configurat ion information.
Smoke Detector/Fire Shutdown (FSD) — This function is
available only when PremierLink is configured for
(Space) Sensor Mode. The unit is factory--wired for
PremierLink FSD operation when PremierLink is
factory--installed.
On 48TC units equipped with factory--installed Smoke
Detector(s), the smoke detector controller implements the
unit shutdown through its NC contact set connec ted to the
unit’s LCTB input. T he FSD function is initiated via the
smoke detector’s Alarm NO contact set. The PremierLink
communicates the smoke detector’s tripped status to the
CCN building c ontrol. See Fig. 25 for unit smoke detector
wiring.
Alarm state is reset when the smoke detector alarm
condition is cleared and reset at the smoke detector in the
unit.
Filter Status Switch — This function is available only
when PremierLink is configured for (Space) Sensor Mode.
PremierLink control can monitor return filter status in two
ways: By monitoring a field--supplied/installed filter
pressure switch or via supply fan runtime hours.
Using switch input: Install the dirty filter pressure switch
according to switch manufacturer’s instructions, to
measure pressure drop across the unit’s return filters.
Connect one side of the switch’s NO contac t set to
LCTB’s THERMOSTAT--R terminal. Connect the other
side of the NO contact se t to TB1--10. Setpoint for Dirty
Filter is set at the switch. See Fig. 55.
R
10
TB1
LCTB
Thermostat
J4-4
PL
Filter Switch (NO, close on rising pressure (high drop))
C08216
Fig. 55 -- PremierLink Filter Switch Connection
When the filter switch’s NO contact set closes as filter
pressure drop increases (indicating dirt--laden filters), the
input signal to PremierLink causes the filter status point to
read “DIRTY”.
Using Filter Timer Hours: Refer to the Rooftop
PremierLink Installation, Start-Up, and Configuration
Instructions (Form 33CS--58SI) for instructions on using
the PremierLink Configuration screens and on unit alarm
sequence .
Supply Fan Status Switch — The PremierLink control c an
monitor supply fan operation through a
field--supplied/installed differential pressure switch. This
sequence will prevent (or interrupt) operation of unit
cooling, heating and economizer functions until the
pressure switch c ontacts are closed indicating proper
supply fan opera tion.
Install the differential pressure switch in the supply fan
section according to switch manufacturer’s instructions.
Arrange the switc h contact to be open on no flow and to
close as pre ssure rises indicating fan operation.
Connect one side of the switch’s NO contac t set to
LCTB’s THERMOSTAT--R terminal. Connect the other
side of the NO contact set to TB1--8. Setpoint for Supply
Fan Status is set at the switch. See Fig. 56.
R
8
TB1
LCTB
Thermostat
J4-6
PL
Fan (Pressure) Switch (NO, close on rise in pressure)
C08118
Fig. 56 -- PremierLink Wiring Fan Pressure Switch
Connection
Remote Occupied Switch — The PremierLink control
permits a remote timeclock to override the control’s
on--board occupancy schedule and place the unit into
Occupie d mode. This function may also provi de a “Door
Switch” time delay function that will terminate cooling
and heating functions after a 2--20 minute delay.
Connect one side of the NO contact set on the timeclock
to LCTB’s THERMOSTAT--R terminal. Connect the other
side of the timeclock contact to the unit’s TB1--2 terminal.
See Fig. 57.
J4-12
R
2
TB1
LCTB
Thermostat
PL
Time Clock
Remote Occupied
C08214
Fig. 57 -- PremierLink Wiring Remote Occupied
Refer to the Rooftop PremierLink Installation, Start-Up,
and Configuration Instructions (Form 33CS--58SI) for
additional information on configuring the PremierLink
control for Door Switch timer function.
Power Exhaust (output) -- Connect the accessory Power
Exhaust c ontactor coils(s) per Fig. 58.
48TC
To Next Page
Loading...
