Carrier PG95SAS User Manual

6
6 15/16
[176.1]
3
[76.2]
3
[76.2]
6 11/16
[170.1]
23 5/16
[592.9]
25 1/8
[638.7]
26 3/8
[670.0]
26 11/16
[678.1]
21
[534.0]
26 5/16
[668.8]
17 5/16
[439.2]
16 9/16
[420.9]
20 1/4
[513.9]
25 3/16
[639.1]
28 3/16
[715.9]
28 5/8
[726.4]
32 5/8
[829.5]
28 3/4
[730.5]
26 3/8
[669.9]
26 11/16
[678.1]
21 15/16
[557.4]
21 1/16
[535.8]
26 5/16
[668.8]
3
[76.2] AIR INTAKE
1 3/4
[44.5] GAS CONN
7/8
[22.2]
7/8
[22.2] POWER CONN
7/8
[22.2]
THERMOSTAT ENTRY
7/8
[22.2]
3
[76.2]
AIR INTAKE
1 3/4
[44.5] GAS CONN
7/8
[22.2]
7/8
[22.2]
3
[76.2 ]
7/8
[22.2]
7/8
[22.2] THERMOSTAT ENTRY
22 15/16
[581.9]
16 9/16
[420.9]
17 7/16
[442.3]
20 1/4
[513.9]
24
[609.7]
28 3/8
[720.4]
28 5/8
[726.9]
29 13/16
[757]
23 3/8
[592.0]
3
[76.2]
VENT
1 (BOTH SIDES)
[25.4]
D
2 3/10
[58.4]
C
BOTTOM RETURN
WIDTH
11/16
[17.5]
11/16
[17.5]
B
OUTLET WIDTH
A
22
[558.3] (BOTH SIDES)
14 13/16
[376.3]
35
[889.0]
5/8
[15.8]
1 5/16
[33.3]
29 1/2
[749.3]
19 1/8
[485.8]
20 5/8
[522.7]
23 7/16
[595.6]
[101.6]
4
[63.5]
2 1/2
18 1/16
[458.6]
2 1/2
[63.5]
4
[101.6]
20 5/8
[522.7]
BOTTOM INLET
21 5/8
[549.5]
6 1/16
[154.0]
PART NUMBER
SD5024-4
SHT
1
REV
E
NEXT SHEET
2
VENT
AIR INTAKE
AIR FLOW
AIR FLOW
SIDE INLET
SIDE INLET
CONDENSATE DRAIN TRAP LOCATION
NOTE: ALL DIMENSIONS IN INCH [MM]
[22.2]
7/8
7/8
[22.2] POWER CONN
AIR FLOW
SEE NOTE #3
NOTES: 1. Doors may vary by model. 2. Minimum return-air openings at furnace, based on metal duct. If ex duct is used, see ex duct manufacturer's recommendations for equivalent diameters. a. For 800 CFM-16-in. (406 mm) round or 14 1/2 x 12-in. (368 x 305 mm) rectangle. b. For 1200 CFM-20-in. (508 mm) round or 14 1/2 x 19 1/2-in. (368 x 495 mm) rectangle. c. For 1600 CFM-22-in. (559 mm) round or 14 1/2 x 22 1/16-in. (368 x 560mm) rectangle. d. Return air above 1800 CFM at 0.5 in. w.c. ESP on 24.5" casing, requires one of the following congurations: 2 sides, 1 side and a bottom or bottom only. See Air Delivery table in this document for specic use to allow for sucient airow to the furnace. 3. Vent and Combustion air pipes through blower compartment must use accessory “Vent Kit - Through the Cabinet”. See accessory list for current part number.
TOP VIEW
A12267
59SC2
FURNACE SIZE
A B C D
SHIP WT.
LB (KG)
CABINET WIDTH OUTLET WIDTH BOTTOM IN LET WIDTH AIR INTAKE
040---10
14---3/16 (361) 12---1/2 (319) 12---9/16 (322) 7---1/8 (181)
121.0 (55.0)
060---12 125.0 (56.8)
040---12
17---1/2 (445) 15---7/8 (403) 16 (406) 8---3/4 (222)
132.0 (60.0)
060---16 142.0 (64.5)
080---16 151.0 (68.6)
080---20
21 (533) 19---3/8 (492) 19---1/2 (495) 10---1/2 (267)
158.5 (72.0)
100---16 166.5 (75.7)
100---20 166.5 (75.7)
120---20 24---1/2 (622) 22---7/8 (581) 23 (584) 12---1/ 4 (311) 184.0 (83.6)
Fig. 1 -- Dimensional Drawing
59SC2C

Carrier PG95SAS Specifications

General

Brand	Carrier
Model	PG95SAS
Category	Furnace
Language	English