Need help?Do you have a question about the Carver 2767 SANTEGO and is the answer not in the manual?
Details Carver's warranty policy for its boats.
Information about pre-delivery service procedures.
General information regarding warranty coverage.
Procedures for second owner registration.
General information and warnings about engine and drive systems.
Information on engine exhaust, carbon monoxide hazards, and prevention.
Details on stern drive systems, operation, and warnings.
Explanation of engine cooling systems and maintenance.
Explains propeller diameter, pitch, and slip.
Overview of engine instruments for monitoring operational condition.
Details on tachometer, gauges, alarms, and synchronizer.
Discusses remote control systems, throttle, and shift cables.
Explains operation of controls, dual engines, and synchronization.
Describes the function of the neutral safety switch.
Operation of controls on dual station boats.
Periodic inspections, lubrication, and adjustments for control systems.
Details the rack and pinion mechanical steering system.
Explains the helm assembly, reservoir, and hydraulic cylinder.
Device indicating stern drive position relative to ahead.
Explains propeller torque and its effect on steering.
Describes the power assist steering system.
Maintenance of steering cables, linkage, and helm assemblies.
Overview of 12V DC and 120V AC electrical systems.
Installation and operation of single and dual battery systems.
Installation and operation of a single 12V DC battery system.
Installation and operation of dual battery systems using selector switch.
Guidelines for keeping batteries charged and clean.
How to use and read the voltmeter for battery monitoring.
Details helm, interior, and additional 12V equipment.
Information on the boat's AC electrical system.
Explanation of the three-wire, color-coded AC circuitry.
Procedures for connecting and operating dockside power.
Guidelines for connecting shore power cords and adapters.
Types of electrically induced underwater corrosion.
Procedures for testing the gasoline fuel system.
Location and type of fuel fill plates.
Information on fuel tank vents and their maintenance.
Function of anti-syphon valves in fuel withdrawal lines.
How the fuel gauge indicates fuel level.
Importance of cleaning fuel filters for engine supply.
General use and maintenance of fuel systems.
Overview of the fresh water supply system.
Details on the cold, fresh water pressurized system.
Capacity and location of water heaters for different models.
Steps to prime the water system after filling.
How the pressure water system operates.
Information on pressurized hot water systems.
System for using sea water for cleaning purposes.
System designed to meet engine compartment ventilation requirements.
Describes air intake and exhaust components for ventilation.
Use of electric bilge blower for ventilation.
Periodic inspection and cleaning of ventilation ducts.
How cabin side windows and hatches provide ventilation.
Function and control of bilge pumps.
Drainage of sealed compartments behind bulkheads.
Information on self-contained, manual, electric, and crown heads.
Dual voltage refrigerators, operation, and care.
Information on alcohol and alcohol-electric stoves.
Description of cassette stereo and AM/FM radio.
Operation of AC units and cooling medium.
Importance of spotlights for safe cruising at night.
Value of a compass and proper calibration.
Numeric readout of elapsed engine operating time.
Information on depth sounders for various models.
Electric/hydraulic trim tabs for hull control.
How to operate trim tabs for bow up and bow down.
Proper techniques for using trim tabs for efficiency.
Safety rails, gates, and hardware maintenance.
Information on fiberglass swim platforms with ladders.
Design and use of bow pulpits for anchoring.
Details on Halon and hand-held fire extinguishers.
Drop-in cushions for additional berth area.
Converting dinette area to a berth.
Convertible aft deck lounge seating.
Care for exterior and interior upholstery.
Removal, cleaning, and re-installation of draperies.
Protective covers for bridge, cockpit, and side curtains.
Advisable covers for winter dry dock storage.
Design principles of Carver boats and hull construction.
Materials and techniques for fiberglass components.
Procedures for installing equipment to fiberglass components.
Care for fiberglass surfaces, including cleaning and waxing.
Importance of proper hull support when out of water.
Steps for repairing cosmetic damage and blisters.
How to care for teakwood to maintain its appearance.
Care for Decragard panels, including cleaning and waxing.
Care for laminate, plexiglass, and dash panels.
Steps for preparing the boat for winter layup.
Procedures to perform after the boat is lifted.
Final checks and preparations before winter storage.
Maintenance schedule for engines and drive systems.
Maintenance schedule for control systems.
Maintenance schedule for steering systems.
Maintenance schedule for electrical systems.
Maintenance schedule for fuel systems.
Maintenance schedule for the fresh water system.
Maintenance schedule for ventilation and drainage systems.
Maintenance schedule for interior equipment.
Maintenance schedule for exterior equipment.
Maintenance schedule for seating and weather covers.
Maintenance schedule for fiberglass hull and components.
Maintenance schedule for woodwork care.
Becoming familiar with boat systems and operation.
Understanding boat systems and manufacturer information.
Required safety equipment and federal requirements.
Essential rules for safe boating operation.
Items to check before starting the engines.
Checks to perform after the engine has started.
Warnings and procedures for grounding and towing.
Definitions of nautical terms and phrases.
To Next Page
General