CARVIN 1588 - User Manual

MODEL 1588 SPEAKER SYSTEM SPECS:
Frequency Response: 45 Hz to 19 kHz ±3 dB
Useable Low Frequency: 34 Hz (-10 dB)
Power Handling: 800w Continuous Power
Recommended Amp: 100 to 1200 watts
Sensitivity: 103 dB SPL, 1 Watt @ 1 meter
Coverage Angles: 90° Horizontal, 45° Vertical
Nominal Impedance: 4Ω
Crossover Type: C1588 Constant Voltage
Inputs/Outputs: Two 1/4", two Twist-lok™
Bi-Amp Support: Yes—Panel Switch
Horn Driver Protection: Yes–Relay Dimming
Woofer Enclosure Type: Vented Box
Enclosure Covering: Black Duratuff II™
Dim/Wt: 25"W x 19.25"D x 48.5"H, 124 lbs.
Optional Cables: PH50, SPK25, SPK50, SPK100
Optional Vinyl Cover: CVS1588
1588 FREQUENCY RESPONSE
CARVIN ENGINEERING DATA 1588 SPEAKER SYSTEM INSTRUCTIONS
1588
Congratulations on your selection of the 1588 loudspeaker. As the big brother of the 3-
way 1584, the 1588 Loudspeaker benefits from the same state-of-the-art design and
response characteristics, but with one obvious difference—it has twice the size, with twice
the components. This translates into an obvious benefit—much more sound output and
power with the same extraordinary response as the smaller version. In fact, there isn't any
application that this 800 watt 3-way system can't handle, tackling anything from large
clubs to outdoor concerts. Like the smaller 1584, the 1588 gives you what other 3-way
loudspeakers don't—studio quality sound in large sound reinforcement applications.
The low frequency subsystem of the 1588 utilizes two heavy-duty 15” woofers, chosen
for their extended bass response at high levels. The midrange employs two 8” direct
radiating midrange drivers, for their exceptionally smooth and extended frequency
response. The high frequency consists of one highly accurate titanium horn driver and
lens assembly. All components are integrated with our 3-way C1588 crossover to deliver
a system response that is smooth from 34 Hz to 19k Hz. Bi-amping can easily be done
by selecting the bi-amp switch and input connectors.
RECEIVING INSPECTION
INSPECT YOUR SPEAKER FOR ANY DAMAGE which may have occurred during
shipping. If any damage is found, please notify the shipping company & CARVIN.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship
your unit, always use the original carton and packing material. This will provide the best
possible protection during shipment. CARVIN and the shipping company are not liable
for any damage caused by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped
separately. Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card. Keep your portion of
the card and return the portion with your name and comments to us.
WARRANTY
Parts and labor are covered for 1 year on manufacturer’s defects. Warranty does not
cover burned out drivers caused by excessive power or distortion, or physical damage
caused by general use, moisture or dust. CAUTION: Distortion from power amps can
destroy drivers much faster than clean power. Contact Carvin’s Customer Service at
800-854-2235 or returnsrepairs@carvin.com. Customer is responsible for shipping
charges.
TYPICAL LOUDSPEAKER IMPEDANCE CONFIGURATIONS
Individual speaker or speaker cabinet wiring examples for total impedance.
SERIES CONNECTION
16Ω TOTAL IMPEDANCE
+
+
+
PARALLEL CONNECTION
4Ω TOTAL IMPEDANCE
+
+
+
8Ω TOTAL
IMPEDANCE
SERIES/PARALLEL
CONNECTION
8Ω TOTAL IMPEDANCE
+
+ +
+
+
+
+
8Ω
8Ω
8Ω
8Ω
8Ω
8Ω
8Ω
4Ω8Ω
8Ω
16Ω8Ω8Ω
76-01588 0902
12340 World Trade Drive, San Diego, CA 92128
(800) 854-2235
www.carvin.com
SPEAKER CABLES
Use either 1/4” 16 gauge copper wire speaker cable or high-current Twist-Lok™
cables with heavy 4 conductor 12 gauge copper wire. The Carvin PH50 is
adequate for lengths up to 50’ under normal use. You can DAISY-CHAIN up to one
additional speaker per cable by using the OUTPUT connector. Be sure to note the
total impedance to the amp so it is not lower than it’s recommended impedance.
See Typical Loudspeaker Impedance Configurations.
SUGGESTIONS FOR OPTIMAL PERFORMANCE
Raise the enclosure to the ear level of your audience for greater coverage. To
help control feedback, keep the speakers in front of the microphone. Never direct
the microphone towards the speaker. Use a graphic EQ for further feedback
control. For greater coverage, add a second speaker system 20° to 30° off axis.
REAR CONNECT PLATE
Two standard 1/4” phone jacks and two Twist Lok™ connectors are featured.
See hookup diagrams for full range and biamp options.
1588
FULL RANGE
BIAMP
Serial No.
MADE
AUS
IN THE
xxxxxx
POWER RATING: 600 Watts
PRO SOUND REINFORCEMENT
IMPEDANCE: 4 Ohms
BIAMP—LOW FREQ. BIAMP—HI FREQ.
TWIST-LOK
FULL RANGE MODE:
JACKS WIRED
IN PARALLEL
1+
1–
SIGNAL
GROUND
2+
2–
NOT USED
NOT USED
MIXER
POWER AMP
OUT
MODE SWITCH: FULL RANGE
ADDITIONAL
SYSTEM
1588
FULL RANGE
BIAMP
Serial No.
MADE
AUS
IN THE
xxxxxx
POWER RATING: 600 Watts
PRO SOUND REINFORCEMENT
IMPEDANCE: 4 Ohms
BIAMP—LOW FREQ. BIAMP—HI FREQ.
TWIST-LOK
FULL RANGE MODE:
JACKS WIRED
IN PARALLEL
1+
1–
SIGNAL
GROUND
2+
2–
NOT USED
NOT USED
MODE SWITCH: BIAMP
ELECTRONIC CROSSOVER
MIXER
OUT
IN (Set FREQ 600Hz) HILOSUB
MIXER
NORMAL FULL RANGE HOOKUP
BI-AMP HOOKUP
See other side for SPS™ Powered Speaker operation
For your records, you may wish to record the following information.
Serial No._____________________ Invoice Date_______________

Summary

1588 Speaker System Overview and Specifications

System Introduction

Introduction to the 1588 loudspeaker, its design, and component features for high-level applications.

Technical Specifications

Detailed specs including frequency response, power handling, sensitivity, coverage, and impedance.

1588 Speaker System Connections and Operation

Connectivity and Hookup

Details on rear panel connectors, full range vs. bi-amp hookups, and cable requirements.

Usage and Performance Tips

Guidance on optimizing sound, controlling feedback, and maximizing speaker coverage.

Impedance Configurations

Examples of wiring configurations for different total speaker impedances.

1588 Speaker System Handling and Warranty

Receiving and Shipping

Instructions for inspecting for shipping damage and retaining packing materials for returns.

Warranty Information

Details on warranty coverage, exclusions, and contact for service or repairs.

1588 P Powered Speaker Operation

SPS Powered Speaker Features

Highlights of Carvin's SPS powered speakers, including advanced electronics and efficiency.

Input and Level Control

Guidance on input connections, using the 12dB pad, and soft limiting for optimal audio levels.

Power and Protection Indicators

Explanation of the power switch LED status (GREEN for normal, YELLOW for protect).

Rear Powered Connect Plate

Details on the rear panel connections for the 1588P, including inputs, outputs, and power.

Powered Amplifier Specifications

Technical specifications for the 1588P powered amplifier, including power, THD, and efficiency.

CARVIN 1588 Specifications

General

Brand	CARVIN
Model	1588
Category	Speaker System
Language	English