CAS XE 300 User Manual

2
XE 영문

CAS XE 300 Specifications

General

Brand	CAS
Model	XE 300
Category	Scales
Language	English

Summary

Introduction

Installation

Unpacking

Lists components included with the scale.

Selecting the location

Guide on choosing a suitable operating environment for the balance.

Leveling the scale

Instructions on how to level the balance using its feet.

Loadcell Protection

Instructions on how to protect the load cell by locking it.

Replacement Mercury battery (RTC battery - CR1220)

Steps for replacing the RTC battery (CR1220) in the scale.

Overview of Display Indicators and Keypad

Display

Explains the various indicators and segments on the scale's display.

Keypad design

Illustrates and describes the layout of the scale's keypad.

Operations

Zero the display

How to set the display to zero, including auto zero-setting.

Tare

Instructions for using the tare function to subtract weight.

Weighing operation

Steps for performing a standard weighing operation.

Counting operation

Guide on using the counting mode with sample data.

Percentage weighing

How to perform percentage weighing with sample data.

Density measuring

Steps for measuring the density of an object in water.

Hold function

Averaging unstable readings and extending display information.

Check function

Setting high and low limits for weighing checks.

Units available

Lists the various weighing units supported by the scale.

User Menu Setting (OIML Approval ver.)

Initial Unit (OIML Approval)

Setting the initial unit of measurement.

Auto shut off time (OIML Approval)

Setting the duration before the scale automatically powers off.

Serial port setting (OIML Approval)

Configuration of serial port communication settings (R1, R2, USB).

Data Transmitting mode (RS232C2, OIML Approval)

Configuring RS232C2 data transmitting modes.

Baud rate (RS232-2, OIML Approval)

Setting the baud rate for RS232-2.

Data transmitting mode (USB, OIML Approval)

Configuring USB data transmission modes.

Unit Weight re-computing (OIML Approval)

Setting to re-compute unit weight for counting applications.

Check alarm mode (OIML Approval)

Configuring the scale's alarm mode (Unstable or Stable).

Check alarm type (OIML Approval)

Setting the type of check alarm (IN or OUT).

IR key function (OIML Approval)

Configuring the functions assigned to the IR key.

Date and Time setting (OIML Approval)

Setting the current date and time on the scale.

Printed date format setting (OIML Approval)

Choosing the format for printing dates.

Backlight (OIML Approval)

Adjusting backlight settings for the display.

User Menu Setting (N, H type only)

Span Calibration

Procedure for calibrating the scale's span.

Initial Unit (N, H type)

Setting the initial unit for N, H type models.

Units available (N, H type)

Selecting which weighing units are enabled on the scale.

Auto shut off time (N, H type)

Setting the duration before the scale automatically powers off.

Serial port setting (N, H type)

Configuration of serial port communication settings (R1, R2, USB).

Data Transmitting mode (RS232C2, N, H type)

Configuring RS232C2 data transmitting modes for N, H types.

Baud rate (RS232-2, N, H type)

Setting the baud rate for RS232-2 on N, H types.

Data transmitting mode (USB, N, H type)

Configuring USB data transmission modes for N, H types.

Unit Weight re-computing (N, H type)

Setting to re-compute unit weight for counting applications.

Check alarm mode (N, H type)

Configuring the scale's alarm mode (Unstable or Stable).

Check alarm type (N, H type)

Setting the type of check alarm (IN or OUT).

IR key function (N, H type)

Configuring the functions assigned to the IR key.

Date and Time setting (N, H type)

Setting the current date and time on the scale.

Printed date format setting (N, H type)

Choosing the format for printing dates.

Backlight (N, H type)

Adjusting backlight settings for the display.

Stable class range (N, H type)

Adjusting the range for stable weighing detection.

Zero display range (N, H type)

Setting the range for zero display stability.

Zero return range (N, H type)

Configuring the range for automatic zero return.

Zero tracking range (N, H type)

Setting the range for automatic zero tracking.

Power Supply

AC/DC Power

How to connect and use the AC/DC power adapter.

Battery Power

Information on using dry cell or rechargeable batteries.

Data Transmitting

Interfaces

Details the available RS232C and USB interfaces.

Communication settings (For RS232C-2)

Specifies communication parameters for RS232C-2.

Date format

Describes the data formats for different protocols.

Variables (For LP-50 and BP DT-4 Printer)

Lists variables for LP-50 and BP DT-4 printers.

Error Messages

Data sheet